Toyota Camry
Q: flasher unit located and get a diagram of on a 1994 ford thunderbird?
Answer : <br> <br> there no flasher unit. spray wd40 around 4way flasher switch on top of <br> steering column. operate switch a times. worked for me on 94 t-bird.
Q: a purge flow in a toyota camry 1999 le?
Answer : purge flow a term used in evaporation system....or emmisions system. there a puge valve solenoid controlled. vapors purge into intake while car running. if get code and gas cap tight. something amiss with fuel system tightness.
Q: fusible link in a 1996 ford contour and hard to replace?
Answer : if there fuse links on car, there not be one, there be several, but contour doesn't use any "fuse links." uses fuse link cartriges. large fuses in engine compartment fuse box have clear windows on top. to replace lower amp fuse cartridges, simply pull them out. high ampere fuse cartridges(80 amps and above) held in with screws on each blade terminal.
Q: break loose crankshaft pulley bolt on a 1988 honda accord?
Answer : best method for removing crankshaft pulley retainer bolt with an impact gun/wrench. 1. remove tire on driver's side of car. there an access slot on side of wheelwell insert a socket with an extension onto bolt and remove it. 2. bolt size 17mm. use an impact socket, as anything less may split under impact of wrench torque. additionally, there a specialized tool designed to hold pulley while turning bolt, but tool may not be necessary if an impact wrench used. an indicator may need specialized tool if pulley itself rotates as use impact wrench in attempt to remove bolt.
Q: problem 1988 camry blower switch only works on two high speeds?
Answer : defective fan motor assuming talking about heater,two likely senarios fan motor burned out on one speed or fan switch defective. also be a wire problem but highly unlikely because ti a plug in most likely result in complete failure. geuss to be fan motor burned out on one speed. at some point, probably work only on one speed and then burn out completely. same problem and "blower motor resistor box" located right next to blower motor. if blower motor works at all fine. speed at turns regulated by resistors limit amount of current flows to motor. possible switches be faulty but since there two bad doubt issue.
Q: replace an ignition coil in a toyota camry?
Answer : have to take off distibutor cap. be able to see coil immediately. then unscrew bolts connecting wires and unscrew ones on bottom. they're hard to get to so might have to take a hose or two off to reach better. if can't get out might have to take distributor itself out sucks because have to be careful about timing. if timing off, car backfire it's started. after get coil off, replace with new one, hook up wires again and put cap back on. don't forget to disconnect battery while this.
Q: 'pwr' light on dash mean on a 1989 camry on continually?
Answer : well, as i've owned a toyota camry before, advice be to you, check for a button with "pwr" on (usually near gear shift). most manual cars have a "power" and "economy" mode in them. "pwr" light on dash probably means you've got vehicle in "power" mode. find button. turn off. problem solved :p have fun!
Q: transmission fluid drained?
Answer : there a drain plug in pan or if there isn't then have to remove pan
Q: keep getting 'egr' fault on 2000 chevy metro even after replacing egr valve be problem?
Answer : using diagnostic tool reads engine codes, clear out codes and try reading again. same problem on 97 geo metro. if answer above didn't help, replace o2 sensors, and retry above answer.
Q: set time on balance shafts to crankshaft on a 1992 2.2 camry?
Answer : balance shafts on a 2.4 toyota camry, proper timing?
Q: replacing oxygen sensor shut off maintenance required light on a 1992 jeep cherokee?
Answer : take off positive battery cable, whereas power source for vehicle. leave cable off for 30 minutes then place back on. once on, turn over ignition so radio, interior lights etc.. come on. let sit for 20 seconds, then start vehicle. eliminate maintenance light. if comes back on within 10 minutes, may want to have a computer diagnostics done on vehicle; to look for faulty codes etc...
Q: wrong clutch pedal stays at bottom of floor doesn't come up?
Answer : one of two possibilities. check master clutch cylinder container to see if fluid all leaked out. if has, chances are, either master or slave cylinder need to be replaced. a mechanic fixed mine and wrote on repair workup replaced master clutch cylinder, however upon subsequent investigation, discovered actually replaced slave cylinder, refilled with dot fluid and rebled cylinder. fixed problem described for me, on a 97 honda accord. fixed a 2003 accord and i'm fairly sure all hondas use hydraulic clutches. stepped on clutch see clutch lever depress fully and then slowly move back as pressure bleed off. replaced slave cylinder first (it easy to get too) and improved little but then to replace master cylinder to reallly fix it. usually slave cylinders fail first because operate at higher pressure than master. really helps to have a pressurized bleeder because line from master to slave goes up and across back of engine (i think bought mine of ebay) make bleeding all hydraulic systems a one man, fool proof job. also some mechanics have bad results with nonhonda parts. answer 2 above answerer correct. however, another problem cause a clutch pedal to stay down clutch burned out. happened to me a nissan 300zx clutch burned out. two days prior driving and pedal sunk to floor but there still some clutch left. after clutch not disengage anymore and to get fixed. before replacing anything bleed clutch system. wrong with mine. hydraulic or cable? above answers may be correct but assume have a hydraulic clutch. there two types of clutch assemblies, hydraulic clutch aseembly and a cable clutch assembly, if have a cable clutch assembly may be as easy as replacing clutch cable. mine recently broke, made a loud pop tried to shift into gear, took foot off pedal laid on floor. have yet to figure out to replace though, a european spec volvo with little info on on internet.
Q: find factory amp for a 1998 toyota camry?
Answer : amp locationmost amplifiers come stock for stereo under passenger side seat. although some amps located under passenger side seat, amp for 1997 camry located on passenger wall behind glove box.
Q: toyota camry and seems to vibrate a lot only in reverse this?
Answer : bad engine mounts... toyota known for this.
Q: replace a water pump in a 89 toyota camry?
Answer : water pump located under timing belt/ front pully cover need to remove front engine mount,all belts, crankshaft pully, then remove cover ( in two parts) and camshaft /timing belt as drives water pump. good time to also replace belt. best to remove front wheel to get at crankshaft pully
Q: repair for a bent hood loose bumper broken front grate and scratched paint on a toyota camry?
Answer : don't it. got a quote from local junkyard on a hood for a 91 camry and said $100. of course that's without paint, but find same color car to begin with, since camry so common. bumper probably another $100. paint costs them $200-300, probably less. so total cost $500 (without labor, for parts, if did yourself) profiting over $2500 for something be done in a day or two. have a dented hood in a 99 camry right now actually and i'm about to fix myself. sources: boycotting mechanic and doing everything myself for years.
Q: timing belt on a 2001 camry need to be replace and 4-cylinder engine non-interfering?
Answer : 90,000 miles or 72 months. non-interfering engine, at least guarantees nothing happen t-belt to break. most newer engines non-interfering, but doesn't always guarantee anything. owners manual give a maintenance schedule, including schedule for replacing timing belt. don't ignore recommendations, get expensive.
Q: manifold absolute pressure sensor and throttle position sensors located in a toyota camry?
Answer : on a 1992 camry map sensor attached to center of firewall by a bracket and a rubber vacuum hose connected to it.
Q: fuse located on a 1993 toyota camry for power windows?
Answer : most of time window fuse located under hood but aso be in regualar fuse box but if not be in fuse box uder hood fuse box by drivers left knee. above flashers and about 3 inches above circuit breaker for windows and door locks. breaker silver, about 1/2 by 5/8 inch and in center button need to push in to reset. used an unbent paper clip to press it. make sure unit not energized. may need to unplug breaker first. press in center button until clicks.
Q: might brake lights on a 1990 toyota camry not work?
Answer : well if have allready cheaked brake fuse be bulbs have burnt out check that.......as for me tried to go easy way with installing a toggle switch and manually turning them off and on, but today wires melted completely from battery to brake lights themself, as of tomorrow going to buy a brake light switch and install it. told causing all of trouble. hope helped.
Q: change a taillight on a 1986 corvette?
Answer : to replace bulb, remove rear license plate. reach in through opening. squeeze and twist bulb holder. pull out through license plate opening. have a 89 roadster and found out chevrolet only charges $10.00 labor plus price of bulb for any chevy car or truck. after scraping up arms 2 different times, " way to go ", bar none!
Q: paint code on a 1987 toyota camry wagon?
Answer : paint code be on door jamb of car. either right or left sides. ive seen both. next check glove box. if isn't in two places prob doesnt have anymore. if go to a paint supply store (autopaint store) have catalogs of different years and makes of cars. look up code. best to have vehicle there or a piece of vehicle with bc sometimes there called "alternate" colors used on cars.
Q: turn off check engine light on a 1993 ford explorer without taking to a shop then pass smog?
Answer : no, a 93 need to go through full smog test. borrow, rent or buy a code scanner at most auto parts retailers tell computer stored an error code and repair problem. once that, light go off and engine be running cleanly enough to pass emissions. you be able to disconnect battery for 30 seconds and it'll clear but couse of light, problem isn't fixed light may come back and if causing engine to run pooly yes fail
Q: replace an interior door handle on a toyota camry?
Answer : interior door handle in a toyota one of easiest things to replace. first purchase a new interior handle for said car. then look for any screws in door panel (usually in plastic trim pieces such as a door pocket or with a plastic flip-cap on them)and remove them. then use a door panel removal tool (auto parts store in "help" section $5.00) to pop plastic retainers behind panel (from 6 to 10). there be a plastic trim around handel (screw behind a plastic flip-tab or four point pressure retainer{on corners} need to remove. handle be retained by a screw or two or actually attached to panel. really simple. if change a filter on home a/c unit, this.
Q: check engine error code p0420 on a 2001 sienna?
Answer : po420 catalyst system efficiency below threshold. answer believe catalyst system efficiency below threshold, bank 1. one option. toyota a problem with ecm (engine control module) giving false code and manufactured a new ecm to eliminate problem (ie. old part number 89661-0861 to new part number 89661-08062).
Q: o2 sensor located on a 1992 toyota paseo?
Answer : o2 sensor location oxygen sensor located in exhaust manifold before catalytic convertor. if look down between radiator and exhaust manifold a inches before exhaust pipe connects to exhaust manifold see oxygen sensor. sensor have 2 wires coming from and kinda looks like a sparkplug stuck into exhaust manifold. there 2 nuts hold oxygen sensor into exhaust manifold.
Q: fuel pump relay located on a 1994 toyota camry?
Answer : up butt and around corner if understand question correctly, actually looking for known as "circuit opening relay", may be located behind glovebox, or in main fuse box under hood (look for one labeled "c/opn").
Q: pull lever to pop open gas cap cover on 1999 toyota camry door doesn't pop open even though door be pried open lever pulled up--how fix it?
Answer : hinge on doors tends to rust -- it's a pin inside rolled sheet metal, so capillary action pulls water in and rusts pin. breaks. if you've caught in time, flow some penetrating oil into hinge and wiggle door back and forth till it's free. use some motorcycle chain oil in hinge once a year before snow season to keep salt water out. found interior lever is, in fact, retracting pin in fuel door compartment fine, but mechanism creates spring action to open door pin retracted gone. believe action created by a protrusion on a plastic clip on hinge side of door breaks off over time. protrusion designed to push against a rubber pad closed, creating enough spring action to "fling" door open lever pulled and pin retracts. i'm going looking for a replacement plastic clip. look here as well www.kuehncom.com
Q: cost for a water pump of toyota camry 1999 be time required and labor charge?
Answer : cost for water pump alone runs $40 to $100. time and labor charge to vary from shop to shop. generally take 1 to 3 hours to replace, and charges range from $20-$80 an hour.
Q: brake warning light mean on 1989 buick lesabre?
Answer : brake fluid be low or emergency brake might be partly on. i'd check fluid right away. happened to me and found out rear driver side break like rusted out. be same thing for you.
Q: an ect button on tacoma same as on camry?
Answer : yes, ect stands for electronically controlled transmission. in normal mode get better efficency and greater mileage. in power mode transmission shift points change to allow for more power, at expense of mileage. according to tacoma 2003 owners manual, function of "ect pwr" switch / button located in chapter 'operations of instruments and controls' under automatic transmission section and quoted as follows: "(i) <b>driving in "power" mode (four-wheel drive models and pre runner)</b> in "power" mode, transmission shifted up and down at a higher vehicle speed than in " normal" mode and a more powerful acceleration achieved. to set "power" mode, push in driving patter selector button. power mode indicator light comes on. for ordinary driving, toyota recommends using "normal" mode to improve fuel economy." appear power mode be used towing something or on a difficult incline.
Q: fuse box on 1993 toyota camry?
Answer : check to know whether coolant fan motor needs replacing in 1993 toyota camry v6?
Q: disarm driver side airbag on a 1997 isuzu rodeo and to replace instrument panel light bulbs?
Answer : remove fuse. fuse box located on driver side of dash, between dash and driver side door. <i>note: airbag part of safety systems in car and not be disarmed.</i>
Q: remove rear interior door panel on a 1992 camry specifically inner door handle?
Answer : door handle not be removed till have panel off. remove any screws first ... then slip a screwdriver around bottom of panel and start easing out with a prying motion. follow all around panel, then lift out vertically against window. handle bolted to inner door frame. to completely remove door without breaking handle housing slip two smaller flat head screw drivers at top and bottom of base of handle, housing clips in there, pry gently up on top and down on bottom one and pull housing out from back of housing cause there also a clip in front slides out
Q: leak - suggestions for source - checked and changed oil pan gasket valve cover gaskets rear main seal - seems to be centrally located behind block - 96 grand cherokee ltd thanks?
Answer : a standard chrysler 318 engine. check for oil lines up toward back, and check under intake manifold. there gaskets there like to leak after a while. additional info: might also check oil pressure sending unit screwed into block in a central location under vehicle. two wires going into a plastic piece in turn molded to metal part screws into block. if plastic part cracked and damaged leak oil at location making appear like a possible rear main issue. good luck and hope that's problem because a cheap and easy fix.
Q: am having trouble finding a passenger side rear door skin for a 97 toyota camry le and am wondering if any earlier years compatible?
Answer : hi, out of luck since body style of camry 97, first design for generation. 96 and earlier same down to 92. car be able to use 98 99 quarter panels. be able to get through toyota dealers, but porbably costs an arm and a leg..good luck..
Q: change power steering fluid in a 1995 pontiac bonneville?
Answer : take off serpentine belt unbolt powersteering pump and hoses and drain it. that's it.
Q: change front passenger turn signal light bulb or head light bulb?
Answer : 1696 ford escape headlamp bulbs accessable through a panel under hood. a wire holding closed, push down, and move. instructions in manual accurate for low beam, unplug by squeezing tab, and pulling down. high beam instructions wrong. one unplugs, and have to turn it. use base like a key, and turn counterclockwise. don't know to change turn signal bulb, am still looking. answer been 'cuced'!
Q: engine usually vibrate and cause whole car to vibrate idling in a 1998 ford escort?
Answer : doesn't. it's because of miss-fire. change ignition plugs and some of wiring. a common cause if engine vibrating a leak in a vaccuum hose or a disconnected vaccuum hose. a higher rpms not as noticable. listen for a small air suction noise or if want to rule out simply disconnect a vaccuum line and see if have a noticable change. also might check elbow connects vaccuum lines as sometimes get holes or dissintegrate.
Q: a 1996 toyota camry vibrate at a stop but not while accelerating?
Answer : be timing answer be things. suspect have a vacuum leak.
Q: reset code on 94 camry radio after says help on screen?
Answer : have a 94 camry and need code to unlock radio
Q: might cause a 1992 camry to shimmy between 42and 55 mph?
Answer : possible transmission problem possibly, more likely to be out of balance wheels, worn inner or outer tie rods, incorrect alignment, broken belts in tire, bent rim, or warped brake rotors.
Q: start car doors automatically lock and stop have to manually unlock them in order to get out of car toyota camry le 2002?
Answer : a safety feathure toyota has.
Q: install original fog lights on a 2003 toyota camry?
Answer : to install fog lights on a 2003 toyota camry must first look inside booklet and see foglights go and go on. and however book says to put them on it.
Q: cam position sensor and egr pcv valves located on 2000 camry v6?
Answer : don't have pictures but found some by googleing camry egr valve. start there and might be enough to get going.
Q: oil pump in 1997 chevrolet 5.7l silverado?
Answer : drain oil from 1997 chevy 5.7 liter engine oil pan. remove oil pan retaining bolts. remove oil pump retaining bolts. reverse process to install new oil pump.
Q: door locks on 1990 camry unlock making a left turn?
Answer : chances left door missing rubber stop or door gasket isn't as strong as used to be. causes door to wiggle turning left or hitting bumps and triggers locking mechanism enough to flip it. check both doors for identical trim , rubber gaskets and stops. see if any of them flat , broken or missing and replace them. once door fits snuggly again may fix problem. good luck may
Q: change headlights on a 1986 ford tempo?
Answer : probably need to fill headlight fluid. check at wal-mart.
Q: power steering fluid reservoir located on a 1990 oldsmobile cutlass supreme with a 3.1 liter engine?
Answer : steering fluid reservoirunder hood, passenger side, above serpentine belt.
Q: locate engine number on a toyota camry?
Answer : here's a pdf file answer question in detail. http://www.etimago.com/yaris/tsb/t-sb-0301-08%20(engine%20serial%20number%20location).pdf
Q: have in common toyota camry 2000 ce trunk lid brake lights check engine light p1780?
Answer : solved nobrake lights check engine p1780three broken wires @ driver's side trunk lid hinge.one day, dash fault rear-light indicator came on. awhile later, check engine light came on. someone push brake pedal while checked rear lights. brake lights on trunk lid did not come on. night, replaced both bulbs in parts store parking lot. backed up to parts store window to view operating lights in reflection. dark so lights on. hit brake pedal, lights on trunk lid dimmed. no brake lights. next day, in day light, inspected wiring @ light sockets and visually followed wire harness pass hinge to ducks behind a side panel. before ducked behind side panel, noticed two broken wires. at closer inspection, noticed a third ready to break. spliced in three new pieces of wire. one problem solved. evening went to autozone. check engine light code p1780. scoured www for a solution. none. next morning, started car to drove to work. no check engine light. another problem solved by fixing three wires? code p1780 for a problem with park/neutral position switch. at least one of wires repaired must have been for backup lights, computer no longer saw problem so turned out "check engine" light.
Q: cost to replace clutch on a 1991 toyota camry 4 cylinder?
Answer : paid 552.00 in november of 2005. another response: in 1998, paid about $600 at alexandria va dealership for a 91 4-cylinder dl camry. paid about $1000 from same dealer in 2004. another clutch job done in february 2009 by an independent shop for $1100. all jobs included a new clutch plate, clutch bearing, and pressure plate. lots of labor involved.
Q: change a power antenna on a 2000 corvette convertable?
Answer : get instructions on replacing a power antenna on a 2004 corvette convertible?
Q: deactivate factory alarm on a 1997 toyota celica lost remote?
Answer : try to start engine a times. on then off on then off turn off after a couple tries happened to me a several times remote on fritz.
Q: not working cable ok part in 5speed tran not fix toyota supra 1988?
Answer : have to check a part between cable and trans, theres a little part connect two, gets worn.
Q: a toyota camry easily turn right but be be nearly impossible to turn back left while car running but turned off wheel be turned either way?
Answer : check "rack and pinion" assembly. probably have a bad internal seal. answer have a bypass on one of teflon rings on spool valve inside rack. housing have a groove worn into it's by passing. have a fault on spool valve. www.powerbrakeandsteering.co.za
Q: 1999 toyota camry battery type 24r by a type 35dl by mistake and having car hesitation problems afterwards accelerating related or think any problems might occur?
Answer : probably not related, if batt new and alternator good then an off sized batt wont cause an issue. if ur camry a three liter may have a throttle body issue or more common a egr problem. if feel a hesitation then there a misfire, there a misfire there eventually be a check engine light to tell why. parts stores scan a check engine light for free. if get a code and cant tell google it, or re post on here. hope helps.
Q: to install 6x9 speakers in toyota camry?
Answer : 1. remove back bottom seat by pulling out. <br> 2. remove 2 side cushion by unbolting <br> 3. take out black armor piece in back of back seat. use a screw driver to pick out black things hold in. <br> 4. gently remove tail light. then unplug. <br> 5. move big fat thing blocking ur speakers. there safety anchors with caps on it. remove cap by pressing outer shell outwards(took me a while first time) <br> 6. now see speakers, use a screw driver to pry speakers up. speakers glued to car. try to use toyota speaker adapter plugs so don't need to cut wires and mess electric system up. get them from ebay or amazon.
Q: firing order for 1990 v6 toyota camry?
Answer : from chilton's manual at library... 1,2,3,4,5,6 and back wall cylinder numbers 1,3,5 and front 2,4,6 ... all from left to right or from belts towards distributor.
Q: miles timing belt be replaced on a 96 ranger 4-cylinder?
Answer : usually reccommend about every 90,000 miles.
Q: replace side mirror for 2000 toyota camry?
Answer : replace a drivers side mirror on a 200 toyota camry? replaced right side mirror on a 2000 toyota camry. attached to car with 3 bolts. open car door and one of 3 bolts easily seen by removing a round plastic cover on bolt screw. easily done by hand. there a 10mm nut on thread then by unscrewed. two bolts inside of triangular inside panel forward of side door window. car worked on a small speaker in panel. panel a hinge clip on bottom and pushed in at top. to remove it, pry panel open by inserting a screwdriver underneath top point of triangle and separate from door frame. be gentle and go deep enough not to break plastic , but then pop loose. then two bolts and nuts be visible. remove two remaining nuts holding mirror on to car. also remove electrical connector attaches to motor in mirror. may be a little difficult because of locking knob on connector. used a small screwdriver to open up a little. now outside mirror be removed and new mirror assembly replaced in three holes. if side panel a speaker, speaker bracket be placed onto bolts before nuts screwed onto bolts. after all nuts tightened and electrical connector reinserted, triangular plastic panel be replaced. line up hinge clip at bottom of panel with hole in frame at bottom, push in at top and snap in place again. round cover for exposed bolt pressed in place on bolt and job finished. adjust mirror.
Q: remove starter from a 1990 volvo 740 gle?
Answer : take to junk yard starter almost impossible to remove . good luck
Q: change license plate lights on a 2002 toyota camry?
Answer : have to remove liner from inside of trunk lid, then remove connector by turning counter clockwise, then replace bulb, check to make sure working, then reverse to put back. there might be a screw to remove connector, but that's only a maybe...
Q: parts needed to tune-up a 1987 toyota camry le?
Answer : que partes necesito pera hacer el tune up a un toyota acmry 1987
Q: leave overdrive on toyota camry?
Answer : answer ignore previous answer!!!!! yes, must leave overdrive in <i>on</i> position in car and why: transmission comes with a total of 4 gears including overdrive. releasing overdrive only restricts transmission to a 3 gear transmission and therefore <i>not</i> give extra power by turning on (contrary to popular belief). manufacture reccomends leaving overdrive on for best fuel econimy and performance. downshifting to second gear again restricts transmission to a 2 gear transmission (and therefore not <i>only</i> 2nd gear) and again downshifting to 1st gear restricts transmission to only one gear or 1st gear. previous answer wrong. l8r. - ahears.not if want to get best life out of engine and transmission. transmission set up to shift into overdrive whenever possible, to maximize e.p.a. fuel ratings. however, results in engine revolutions per minute being too low for most driving conditions, leads to carbon deposits in cylinders, and excessive unburned fuel having to be processed by environmental controls system. in city, on in hilly terrain, turn overdrive off. cruising on freeway, turn on.
Q: replace air filter on a 2004 toyota sienna?
Answer : if asking about cabin air filter: read on. <b>cabin air filter</b> located directly behind glove box for sienna (ce, le model.) 1. push sides in on glove box to disengage latches. 2. release restraining arm on right side of glove box to release it. 3. behind glove box find filter door push on tabs and release filter door. 4. slide out filter and replace with a new one. 5. reinstall in reverse order.
Q: instrument panel fuse box on 1998 toyota camry?
Answer : instrument panel fuse box next to impossible to find on own. inside car, forward of driver's left knee, behind coin drawer that's to left of steering column. pull out drawer and see fuse block. there's a chart on back of drawer in addition to one inside owner's manual (toward rear of manual on a page that's not referenced in index.)
Q: fix clock on a toyota camry?
Answer : if clock in toyota camry stopped working, probably due to a manufacturing defect of clock shows up after a number of years. clock be professionally repaired for a modest fee. reveal around instrument panel on earlier model camry's must be removed to gain access to clock. there some screws holding reveal in place, as well as two friction studs made of plastic. "friction studs" snap into dash at left and right sides of reveal. great care must be used removing reveal to avoid breakage (the friction studs not come out easily). possible to removal, but recommended to have clock removed by an authorized toyota dealership and then send unit in for professional refurbishment. installation of clock and reveal far easier than removal process. note: everyone have a manual for vehicle, and library have a professional shop manual available in reference section.
Q: 4-cylinder 1990 toyota camry dx not getting good gas millege smart to switch to a higher octane gas and best time to this?
Answer : dont waste moneyhigher octane not going to help, it's only for high compression engines to prevent pre-ignition (knock). try a tune up. new fuel filter, air filter spark plugs and wires, pcv valve and a bottle of good fuel injector cleaner add first to gas tank then fill up with gas (techron a good option for this). only situation higher octane help with an engine not requiring if there heavy carbon buildup in cylinders causing pre-ignition and even than it's a temporary fix until be properly cleaned. ________________________________________________________________ agree completely. however, even if don't have a check engine light test oxygen(o2) sensors if handy like that. start to fail without computer knowing by sending erroneous voltages back to computer. be wrong but still within range so computer no idea getting bad information. if replace oxygen sensors must use proper denso sensors. if use bosch or some brand regret it. either fail immediately or give same condition before by giving computer inaccurate information.
Q: ect mean on a toyota camry?
Answer : ect electronic controlled transmission if light comes on, take to dealer. don't have to take to a dealer light comes on. depending on model and year, push a button to turn off and on. like o/d. that's with mine.
Q: replace timing belt on a 2002 toyota camry with 92500 miles?
Answer : toyota recommends timing belts be replaced at 60,000; however, 100,000 miles fine. replace at 100,000 miles as preventative maintenance. 4 cylinder 2002 camry a timing chain not have to be replaced.
Q: access expansion valve on a 1987 toyota pickup?
Answer : replacing expansion valve on toyota p.u.the expansion valve located in and with evaporator, inside evaporator case. case a somewhat square, plastic enclosure located directly behind glove box on vehicle. replacing expansion valve requires removing glovebox and brace in front of it, disconnecting all wiring attached to blower housing (located next to evaporator case, disconnecting hoses attached on engine side of firewall, removing several (10mm) bolts/screws hold evaporator case to firewall and ultimately, removing evaporator case from vehicle. once done, case held together by several philips screws and one or two clips. always 'backup' wrenches removing a valve so as not to rip liquid line or suction line off and always clean mating area of capillary tube and wrap with new tacky tape. don't foget to use new o-rings lubed lightly with refrigeration oil. important to remember to discharge system before procedure using approved recovery/recycling equipment or have done by a qualified technician. also important to note if replacing valve because restricted or exhibiting intermittent closure (which only logical reasons to so, [unless have somehow determined valve itself leaking {very rare for actual valve of type, likely o-rings have corrosive build-up}]) definitely want to remove receiver drier (the system filter), flush system using approved flush method(s) and chemicals and replace drier with a new one. after all, if valve stopped up or acting up, there must be trash in system, and if not flush and replace drier, be doing again in near future! remember not to open drier or install until ready to close system as drier contains dessicant material absorb moisture from atmosphere and be ruined. also, be sure to replace any (refrigeration) oil lost during procedure, plus about 1.5 additional ounces. must also be informed that, as a possible consequence of a restricted expansion valve a system been run for any length of time, there always possibility of a compressor problem (locking up) at some point in future (from oil starvation). before introducing refrigerant to system, system must be 'evacuated' (vacuumed to have air removed). air in system causes corrosive build-up and acids lead to evaporator core and aluminum part leaks. check label on vehicle for proper refrigerant charge. likely somewhere around 32 ounces (r12 type refrigerant. and proper oil 525 viscosity mineral). if system been (properly) converted to r134a, use pag i, or low viscsity (46 weight) oil and about 10 ounces less than r12 charge (if been properly converted. illegal to mix refrigerants and all refrigerants than r12 and r134a not approved by both epa and care manufacturers and some may containg flammable substance [illegal in all states]). good luck and let us know make out. sdi
Q: dipstick used to check oil in a 1988 toyota camry yellow or orange?
Answer : at risk of sounding like a smarty pants. with dip stick
Q: anyone installed fog lights on a 2006 honda odyssey?
Answer : yes there fog lights installed on touring model... think a factory option here instructions for installing fog lights; http://www.handaaccessories.com/odyssey/05odyfoglight.pdf
Q: cause clicking sound from underneath left front wheel or engine toyota camry le 1999 car start to move and disappear car speed increase?
Answer : sounds like a cv axle. (constant velocity axle) part on car turns front wheels. a bar with joints on each end. joints in a rubber boot. sound most likely caused by rubber boot tearing or slipping off and expelling all oil. now joints have no lubricant and probably warped. happend to 1993 toyota corolla 1.8l. to check yourself turn wheel all way to left and park car. make sure turn car off! now lay near front of tire and look behind it. there be bar described. look at rubber boots on each end if don't appear or feel to be torn then not problem. if get fixed. not a severe problem until car makes noise on a strait away but still may want to get fixed. delunatic
Q: be causing a rattling noise and sway in rear of a 1995 toyota camry?
Answer : possibly sway bar bushings. replaced mine on 94 and doing exactly as describe. really not to replace. there a bolt at each end needs to come off and replace it. went to junk yard and picked up two off a car with low mileage and bushings in good shape. usually back sway bars need replaced. there two on each side. try this, jack up car and grab tire at 3:00 and 9:00 (right and left) and see if the wheel moves from side to side. have someone else while look at bushing at end of sway bar and see move if bad. if sway bar good then be solid try to move tire from side to side. only problem changed mine on inner end of sway bar. have to hold end of bolt while loosen nut and head of bolt in a little like cup and there not enough room for a socket and rachet and a wrench not fit in either. bent edge of gas tank up slightly till got a socket in to hold it.
Q: remove lock in cylinder on a 1986 mazda b2000?
Answer : lock cylinder?door or ignition? door simple, remove inner door panel, unhook rods attached to lock cylinder, remove retaining clip
Q: get a timing belt setting diagram for a 2000 renault clio?
Answer : a timing belt setting diagram for 2000 renault clio be obtained through various websites such as "diy","fixya" and "automotive forums". also have one mailed to by contacting manufacturer.
Q: replace a shifter cable on a 1998 toyota camry?
Answer : need to take current shifter cable off, and to so you'll need to open dash and console so reach plate keeping cable in place. next, thread (the replacement) through firewall, and area, and connect it. put everything back together after making sure secure, and you're done.
Q: to replace left front door handle 2002 toyota camry?
Answer : am assuming mean interior, because have same car and both driver's side and passenger side interior door handles have broken. replaced mine today and actually easy, but there a lot of screws to take out. first, need to buy a replacement door handle (i ordered mine from ebay for $15 - and handle metal!! yay!), go to auto parts store and buy a "door upholstery remover" - costs about $10. also need on phillips head screw driver. 2. remove small round screw cover near upper hinge of door and remove screw beneath it. 3. remove black rubber lining/bottom of inner door's pocket - there a screw there and must remove it. then remove panel holds buttons for lock and window control (automatic locks and windows). there a screw beneath panel - so remove screw too. 4. next take off two screws located at bottom of door panel. 5. carefully place all of screws in a safe place not lose them. 6. remove black triangular cover located above upper hinge of door. 7. carefully trying not to break - take off plastic plate lies within door handle casing - covering another screw need to remove. 8. take door upholstery remover and place under edge of door upholstery panel and insert inot fastener as far as possible...then simply pry up. really can't hurt it. (there about 6-10 plastic clips need to be popped to release door panel from actual door. not pry at black clips at top of panel, break them if - act as a kind of hanger clip. 9. door panel now be free from door. carefully take note of there two wires with metal balls on ends (one a white plastic casing while a green casing.). notice white wire on top and green one on bottom. remove wires from broken door handle without breaking them (they not fragile but still be careful). 10. take new handle and place balls of wires into holders of new handle. 11. now put everything back began. am assuming mean interior, because have same car and both driver's side and passenger side interior door handles have broken. replaced mine today and actually easy, but there a lot of screws to take out. first, need to buy a replacement door handle (i ordered mine from ebay for $15 - and handle metal!! yay!), go to auto parts store and buy a "door upholstery remover" - costs about $10. also need on phillips head screw driver. 2. remove small round screw cover near upper hinge of door and remove screw beneath it. 3. remove black rubber lining/bottom of inner door's pocket - there a screw there and must remove it. then remove panel holds buttons for lock and window control (automatic locks and windows). there a screw beneath panel - so remove screw too. 4. next take off two screws located at bottom of door panel. 5. carefully place all of screws in a safe place not lose them. 6. remove black triangular cover located above upper hinge of door. 7. carefully trying not to break - take off plastic plate lies within door handle casing - covering another screw need to remove. 8. take door upholstery remover and place under edge of door upholstery panel and insert inot fastener as far as possible...then simply pry up. really can't hurt it. (there about 6-10 plastic clips need to be popped to release door panel from actual door. not pry at black clips at top of panel, break them if - act as a kind of hanger clip. 9. door panel now be free from door. carefully take note of there two wires with metal balls on ends (one a white plastic casing while a green casing.). notice white wire on top and green one on bottom. remove wires from broken door handle without breaking them (they not fragile but still be careful). 10. take new handle and place balls of wires into holders of new handle. 11. now put everything back began.
Q: replace driver side mirror on a 2003 toyota camry?
Answer : side mirrorselectric, cable operated, or manual? in any case remove driver side door panel, on inside of car in fender side corner mirror mounts, either have a small phillips screw holding mirror backin on, or may have plastic tabs, and be gently popped off using a flat blade screwdriver. once door panel, and inside mirror mount cover removed, see three 10mm nuts, arranged in a triangular pattern behind inside mirror cover. if mirror electric, after removing three 10mm nuts and slowing pulling mirror off on outside, see wiring connector for mirror, unsnap tab and remove mirror. on a note occasionally may be easier to undo mirror if window glass all way down. if mirror manual, remove three 10mm nuts and remove mirror. if a cable operated mirror, with "joystick" to adjust on inside, once three 10mm nuts removed, on inside portion of inside back of mirror, "joystick" held to back cover by a small metric allen screw, with right sized allen loosen screw, but not all way out. after it's loosened sufficiently "joystick" assembly slide right out of cavity it's in. be careful removing mirrors, often times there a rubber grommet any wiring or "joystick" slips through.
Q: turn off check engine light?
Answer : need a scan tool wich be purchased at any parts store or simply disconect battery if a hard code come back on until problem fixed
Q: to put freon inside a 1996 toyota camry?
Answer : go buy "idiots guide to a/c recharging" at a parts stor, includes some freon... also everyone have a manual, and library have a professional shop manual available for copies in reference section (for free)...read up and fix 'em like pro's...! :) dave youll need to locate low pressure line tucked down by passenger side strut, put a gauge on first turn ac on full blast, to make sure problem and not a compressor issue unless already have, put a sealer through first contains a dye and check along all jointed areas manufacturer puts o rings, area's most common for leaks, add one if there no leaks, and re check with gauge, did to girlfriends car and works like a charm, hope helps a little
Q: check air conditioner on 1998 volkswagen beetle?
Answer : air conditorner doesnt blow cold air freeon compressor doesnt kick on
Q: remove rear door off a 1998 toyota camry power windows and locks?
Answer : trim piece covers inside of door pillar must be removed. once removed find a electrical connector release wires for whole door, then unbolt hinges and remove
Q: remove starter on a 1996 toyota 4 runner?
Answer : 1. disconnect battery connectors, or at least positive side.2. disconnect connections on starter, be 2. 1 a locking push on connector a nut. 3. remove bolts hold starter to engine. on v6 there 2 bolts, top and bottom. on 4 cly there be 3 of them, top bottom and out to side.4. here have to make a judgment call depending on type of vehicle. some, like 4 cyl 4 wheel drive model, allow to easily remove out bottom. v6 4 wheel drive model allows to remove out wheel well above suspension arm. a tight fit and need to turn so to get to fit.5 reinstall same way removed.
Q: a charcoal canister on a vehicle?
Answer : captures fuel vapors and prevents them from escaping to atmosphere and then stores fumes and recycles them to fuel tank or engine intake for combustion as needed. long and short of helps to protect environment and improve fuel economy.
Q: thermostat located toyota corolla 2003?
Answer : thermostat located on cooling system on a 2003 toyota corolla. thermostat also be found by following upper radiator hose.
Q: power steering fluid reservoir on a 1988 mercedes 300ce?
Answer : right on top of pump. looks like a european style cartriage oil filter container. but actually fluid reservoir. choosing right fluid tricky part.
Q: reset air bag light in a 1997 toyota camry?
Answer : important to take care of issues have caused warning lights to turn on. an airbag light be reset by clearing code with an obd scanner.
Q: front end vibrates at speeds 40 mph or over new tires new alignment still vibrates more step on gas pedal?
Answer : cv joint bad cv joint? steering box about a bad steering box?
Q: key cylinder toyota?
Answer : hi; ignition key cylinder replace june 9,08 on a 1995 corolla. turn key half way for radio to come on; but not turn all way to start car. found out have to take to dealer to get fix so make keys for it. cost around $425 with keys; a hassel went through.
Q: have a fuse layout for 1991 toyota camry?
Answer : diagrams on cover of fuse boxes...
Q: timing belt need to be changed on a 1997 toyota camry v6 after 60 or 70k?
Answer : send me service manaul to change timing belt on toyota camry v6 97 model timing belt manual or send to me on 5187pox chullora 2190
Q: cause a vibration-roar at a certain rpm on a 1991 toyota camry - there no apparent impact to engine performance roars?
Answer : recently acquired '91 camry 4 cylinder-automatic vibrating/shaking shifts from 1st to 2nd cold. condition goes away after vehicle warms up to operating temps. best guess there something wrong inside transmission, such as improperly adjusted bands or disintegrated clutch discs(?)and perhaps even torque converter. because don't know everything about automatic transmission a guess. well be a broken motor mount or a worn cv axle or loose bolts in engine support braces be causing problem. find solution let know! today put a new cv axle on passenger side because put front of car up on jackstands and let run in gear while crawled underneath and listened and watched heard cv axle making a noise similar to hear vibrates. unfortunately did not fix problem. drove for almost an hour before did vibrating thing, so blows theory only happens engine/trans cold. need to replace cv axle too, and perhaps wheel bearings and rear motor mount, however don't think any of things make vibrating go away. sure feels like transmission to me.:-( called parts house to get a price for a reman unit... omg over $2100!
Q: to fix a power steering pressure tube in a toyota corolla?
Answer : well bought hose to replace mine. paid about $30 for hose itself. haven't replaced yet so don't know long take but don't explect more than about an hour. most shops charge $70-80 an hour. good luck. great cars!!!
Q: change light bulbs for ac and heater controls on dash of a 1999 toyota camry?
Answer : replaced mine a couple months ago and not need to take whole dash apart. pretty simple process. remove ashtray and take out black trim surrounds heater controls and radio. pulls off hard but come off. check online about to remove stereo. knobs for heater assembly pull off and then there a couple screws to remove. expose heater ac assembly. if remember correctly 2 screws remove face plate of assembly and then replace light bulbs behind face plate. have little green sleeves cover bulbs roll off and be put back on new bulbs. good luck. estimated time 30 min at most.
Q: replace radiator coolant?
Answer : to remove coolant from radiator, there a plug or valve at bottom of radiator on either left or right side. loosen and drain coolant into a container---never on ground-it dangerous to animals and toxic. tighten valve empty and refill. run vehicle to get to operating temperature and keep filling until all of air out of system.
Q: replace cigarette lighter on a 1992 toyota camry?
Answer : believe first step to be sure problem actually by attaching test light clip to ground and poking pointy end at center in bottom of socket lighter element plugs in. while key on have power and test light light up. if doesn't light up use test light to check fuses, if find any broken fuses replace them and check lighter again.on '89 camry lighter didn't work and to remove radio to find wire goes to back of lighter come disconnected. in case suspect solve problem by purchasing a new lighter element and/or replacing fuse because seldom anything else goes wrong with cig lighter.
Q: power steering fluid different to brake fluid and also on dash start car brake light lights up mean?
Answer : power steering fluid completely different from brake fluid and not interchangable. don't know car but in most cases "brake" light in dash a warning light to indicate have a serious problem with brakes. suggest get fixed immediatly. remember, life depends on brakes.
