Toyota Camry
Q: replace fuel filter located on a 1990 toyota camry?
Answer : replace fuel filter located on a 1990 toyota camry?" 1990 toyota camry fuel filter located under air intake hose, disconnect one end of hose from throttil body and end from air filter box.and move hose to side. now see fuel filter. need to use two open end range to disconnect fuel filter.i believe 17 mm, not sure.don't forget to put a piece of rag under fuel filter, because spill some fuel.
Q: check engine light come on in a 1999 toyota camry after 100000 miles to prompt owner to a regular check up?
Answer : 99 camry check engine light observationsdon't want to sound like a "johonny-come-lately" but first contact with group. also have a 99 camry with check engine problem. purchased car used in va and then moved to sc problems really started, although there inklings in va. in searching, found necessary to replace "oxygen sensor" to cure this, did for a measley $300.00. did not solve problem, but delayed for about a year. then replaced gas cap and thought might help, but no cure there either. have been watching cel (check engine light) as relates to weather and conclusion went humidity goes up, light goes on and humidity comes down, light goes off! so all now wait for cooler weather, because here in sc, humidity up most of time in summer. check engine light comes on, a code set into car's control module. need to read codes set. with knowledge determine next step. auto parts stores read code(s) set for no charge if purchase whatever parts nessesary from them to make repairs.
Q: be problem if only 1 automatic seat belt doesn't work in and 89 toyota camry?
Answer : problem most likely broken wire(s) run to door switch (which part of door latch mechanism). look at hinge area of door, and see a rubber boot between door and door frame. inside rubber boot wires run to door switch (and any door electricals). 3 wires for switch thin (22-ish gauge) and tend to break from all of flexing caused by opening and closing door. driver's side fails frequently because gets used more often than passenger side. need to fix (or replace) wires. remove door's trim panel, pop loose some of wiring harness hold downs (for better access), and pull boot's grommets loose from door and door frame. remove kick-panel trim to gain access to harness connector and disconnect. pull connector through door frame into hinge area. give plenty of access to wiring so slide boot away from damaged area. fix broken wire(s) and reassemble everything. 1991 camry shoulder belt won't returni don't have answer but am looking to solve same problem on a 1991 camry. automatic shoulder belt not track back towards seat. passenger side works fine. i've checked all fuses and breakers, they're ok. with drivers door closed, manually rolled top belt motor wheel in order to retrieve track/belt into return position. then opened door and motor operated releasing shoulder belt in forward position as - motor sounded and worked fine. won't reverse to come back. any ideas?
Q: disable seatbelt warning chime on a 1990 nissan 240 sx?
Answer : obviously, buckling seatbelt silence reminder. if see/hear reminder and all belts used by reminder buckled, vehicle be taken in for service asap. if not want to use seatbelt for whatever reason, and wish to disable or silence reminder system altogether, be done in a matter of minutes by a serviceperson at a dealership using a custom option setting device connected to vehicle's internal computer. as a safety system, some dealerships may not be willing to unless sign a liability waiver. however, if not wish to have vehicle serviced professionally for whatever reason or like to disable or bypass seat belt reminder system for certain seats only, following options may be of help: a piece of sheet metal of same dimensions and shape as actual seat belt 'plug' be inserted into seat belt 'socket' to silence reminder. obviously, more piece of metal resembles actual 'plug', more likely to work. also, as seat belt buckle design not changed lately, a junkyard one source of seat belt 'plugs' be cut from straps and inserted in seat belt 'socket' to silence reminder chime. it's likely several model years of a car (and even different makes/models) may all have similar seat belt 'plugs'. lastly, there wires running down 'socket' end of seatbelt tell car's computer if seat belt buckled or not. wires may be cut, stripped and connected together (or separated, depending on stops reminder) permanently. be mentioned disabling or bypassing safety system in any way discouraged by vehicle manufacturers, insurance companies, safety specialists and private and public organizations and individuals. however, there conditions for seatbelt use extremely uncomfortable or presents more harm than benefit, such as in case of certain abdominal/thoracic medical conditions, morbid obesity, etc.
Q: camry 2000 le signals an amber color warning sign car symbol with glow of tail lights meanchecked tail lights and side signal lights and look ok?
Answer : told only one bulb fit high mount tail lamp socket by both repair people and parts store. there are, however, 2, lamps fit socket. if use wrong bulb, dash panel indicator lamp stays on after push brake pedal. if light not come on until first time push on brake pedal after starting car means have a burnt brake light bulb, most times brake light bulb in back window.
Q: change a brake light switch for a 1990 toyota camry?
Answer : to change brake light switch, go purchase one at parts store first so know looking for. then lool behind dash and follow brake pedal up, unhook spring, then keep going up and see switch - unplug it, then loosen nut on switch side of screw. there a nut on side welded into brake, don't mess with one. after loosen nut, unscrew and reverse process to put switch back in... make sure screw in right distance so even a little brake sets off lights... good luck <b>additional information find helpful:</b> difficult to find switch because of location. have to lay head down in footwell as far to left of brake as can, and with back partially inside door and with feet on ground. only way be able to see switch, because body of bracket in way from any angle. need to take a small flashlight and place on top of fuse box and wires to right side of head. aim upward so see switch. also found helpful to remove cover from brake light in back window and turn light toward front so see without having to maneuver in and out of footwell area. following brake pedal arm up see cotter pin and round pin keeps brake pedal arm in place. have to remove pin to release brake pedal arm. once brake pedal arm released and hangs free, see a small, round, black button part of switch. may see 1 to 2 threads coming through welded square nut. on back side of assembly, see remaining threads and body of switch. only be able to reach switch with left hand while in awkward position be in. need a #14 open-end metric wrench to loosen nut secures switch in place. also need to bring as patience as muster up, and take frequent breaks while doing work. am not left handed, but relied heavily on left hand to all work, including removing plug from switch, reinstalling plug into new switch, loosening nut, removing switch, and installing new switch. couldn't anything with right hand because couldn't get into cramped space. a difficult job, but once see for yourself describe above, <b>can</b> get done!
Q: change toyota carina radiator?
Answer : first take out old radiator then put in a new radiator. first make sure have correct make, model, year and engine type before ordering. third party suppliers be cheaper than local toyota dealer, and often deliver to door - carina probably be waiting. buy and replace all hoses, particularly on old bangers like mine - 310,000 kms. if lose drained heating circuit liquid removing old radiator, don't forget to add antifreeze to new one according to climatic conditions. done - sit back and smile contentedly at $$$$s you've saved in labour costs by doing yourself.
Q: torque specifications for a 1996 toyota camry?
Answer : engine? 2.2 litre
Q: remove and replace power steering pump in a 1990 toyota camry?
Answer : replace a power steering pump in a 1990 toyota camry?
Q: have a 91 toyota camry with out rev lights bulbs and fuses ok and shift ind light on dash pr on in park nothing on in reverse and rn on in neutral all ok?
Answer : faulty wires
Q: replace driver's side inside door handle of a 1992 toyota corolla?
Answer : anyone pictures out there for to replace door handles for 92 toyota corolla?
Q: to replace tail light covers for 1999 dodge durango?
Answer : open trunk and there be a couple screws lights are.
Q: please help me with questi1996 toyota camry check engine light on engine quits running while driving wont start for 10 min runs rough plugs and wires replaced egr valve replaced thanks?
Answer : might try computer in car did not expensive well here about 150 dollars or try dealership.
Q: change radio on 1996 camry?
Answer : since wires in a toyota all different colors, all have to go to a car radio store and ask for a car stereo toyota wiring harness. come with intructions but basically all have to plug thing into cars factory harness and hook stereo up. worked for camry 1990
Q: a gas filter in 1994 toyota camry le?
Answer : gas filter in a toyota camry 1994?
Q: change fuel filter on a 1991 toyota camry csi?
Answer : locate it. use two allen wrenches and put one on bottom of filter and top and unscrew really simple.
Q: thermostat located and replace located on a 1998 mercury villager?
Answer : passenger side (front of motor) in middle. above water pump. must remove cover and harmonic balancer to install. difficult.
Q: change headlights on a 1996 cavalier?
Answer : take out 2 bolts on top of light assy and lift up and forward. there a tab on bottom slips into a slot put back in.
Q: to find circuit breaker for power window in 1992 camry?
Answer : circuit breaker for power window in 1990 camry?
Q: lubricate door locks?
Answer : so open smoothly and quietly. <b>ans 2 -</b> if lock in good shape, use <b>dry graphite</b> to lube it. (liquids, even wd40 and similar accumulate dust and cause friction) use liquid penetrants only on old, dirty locks to clean them.
Q: pcv valve located in a toyota corolla 2004?
Answer : pcv valve located on a 2003 toyota corolla? not help! 4 0r 6 cyl? either way pcv (positive crankcase ventalition) valve located on top of valve cover(4cyl) or on one of valve covers(6cyl) a pre-bent black hose from a vacuum source to valve. if there some miles on car break valve and hose(due to being brittle) ever no worries, simply replace valve and use 5/16 fuel line to replace pre-bent vac. hose. may have to tie strap at both ends to keep hose from coming off. valve helps engine from building up too pressure resulting in oil leaks. good idea to change at tune-up time, but over looked by most techs. good luck. master tech 26yrs
Q: type of power steering fluid use on a 1993 mazda 929?
Answer : don't know about a 1993 but 1990 929 takes atf dexron ii for power steering - it's transmission fluid. if don't know, look under hood, there be a diagram of everything car needs. or takes
Q: 1995 toyota camry v6 le making a loud whining noise cold stops car warmed up - any ideas?
Answer : there possibilities for noises such as these. have to think to yourself changes with temperature because happens car warms up. so have a belt squeal or wrong weight of oil causing improper lubrication at lower temperatures or low oil or even bearings in one of accessory drives such as alternator, a c, or power steering units make more noise cold and less warm up. must investigate and give further details for a proper answer.
Q: to disassemble gauges on a 1999 toyota camry?
Answer : take into shop
Q: change spark plugs in a 1993 toyota camry?
Answer : pluygs on a 92-96 camryto change spark plugs on a 1993 camry need following tools: deep well socket set, extension, socket wrench and a piece of rubber tube fit over top of spark plug. go ahead and go to autozone or wherever and buy new plugs. find deep well socket fits it. open hood look for 4 or 6 little black boots sit on a black square on a 4 cylinder sit on top of head and usually be 1st thing see open hood. on 6 cylinder models be on side. grab boot and pull qently but firmly not snatch break. once comes off. put extension on wrench and socket on end fit to end of plug and losen then put piece of rubber tube to top of plug and twist rest of way then pull out put new one on tube and put back in hole and tighten as as with tube then rest of way with wrench. reason difficult to change pllugs on a camry because sunk into heads about 3 inches.
Q: change front wheel bearings on a 1990 toyota camry and tell if really need to be changed?
Answer : front bearings sealed and replaced only become noisy. a badly worn bearing roar at speeds above 40mph and change pitch somewhat as change from lane to lane due to side load placed on it. tire noise (due to tires need rotation) sometimes mistaken for a worn bearing.
Q: prevent a dry start of a 1993 toyota camry v6 engine not been started for one year?
Answer : to remove spark plugs so there no compression (no load on bearings) and crank over motor for 20 seconds then rest starter for a minutes and crank over again; repeat once more. assume have put fresh oil in motor.
Q: 94 toyota camry's driver's side key hole doesn't turn and unlock insert key?
Answer : try lubricating lock with wd-40. work key in-and-out and back-and-forth. if doesn't seem to be working, i'd take to a locksmith shop and have them fix it. happen key gets wet, such as it's raining and key gets wet. happens, be sure to dry key before inserting into ignition.
Q: have a toyota camry with 125000 miles and started to leak transmission fluid serious?
Answer : yes is, have to get looked at asap.
Q: replace an ignition switch on a 1997 toyota camry?
Answer : replace an ignition switch on toyota corolla 1997
Q: change brakes on a toyota sequoia?
Answer : takes about an hour to it. and it's easy.
Q: replace 100 amp alt fuse for a 2000 toyota camry?
Answer : 100 amp fuse replacement not sure , but if talking about 100 amp fuse in fuse box under hood,,here goes.... assuming already have fuse box cover off,,,,remove battery to get out of way,,,remove two bolts holding fuse box ,,,the bottom of fuse box comes off by depressing on each side near bottom,, locate large black and white wires go into fuse,,you'll need a screw driver to un-lock fuse and fuse holder,,pulling slightly on wires while depressing latch ,,it come out from bottom,,,the two wires bolted on to fuse, remove bolts and fuse slide out of fuse holder,,,install new fuse,,bolt wires back in place, insert fuse and fuse holder back into fuse box, replace bottom of fuse box, rebolt to car,,re-install battery... new fuse cost about $10 from toyota dealer. if not asking for,,maybe help someone else.
Q: change a timing belt on a 2000 bettle water pump need to be changed too?
Answer : if milage at or over 60,000 belt be replaced.the water pump as a norm not regulated by milage and may give continual service indefinatly,however 70.00 price tag over 600.00 labor to replace(and seeing as for most part water pump forgoes timing belt and all say if replaceing water pump definitely replace t. belt)i'd recommend doing both and resting assured.
Q: disarm car alarm on a 2001 toyota camry?
Answer : to disalarm alarm on a 1992 toyota camry
Q: firing order for a 1999 toyota camry?
Answer : diagnosing engine problems comes in handy to know engine firing order. for a 1999 toyota camry firing order 1-3-4-2.
Q: fuel filter located and replace on a 2005 toyota tundra?
Answer : as understand it, tundra not have a replaceable fuel filter. there a filter hidden in fuel line inside of frame, but not meant to be changed. call local toyota dealer to verify this. actually, took 04 tundra in for recall ball joint replacements and mechanic recommended change fuel filter. after following fuel line from gas tank, filter appears to be alongside frame below driver's door (under vehicle). appears fairly simple to change. good luck! fellas, there a fuel filter in every car....no such thing as no fuel filter...go to book store or auto store and read haynes or equivalent and show you....you don't even have to buy book, read while in there. good luck! from read...in 2005 and 2006 tundras (1st generation still) put fuel filter in fuel tank! why? don't know.
Q: check engine light on a 2001 toyota camry won't go out?
Answer : light on because computer detected a problem with emissions system. have scanned and problem repaired, and light reset with an obd2 scan tool. not go out until problem corrected. go to autozone for a free diagnostic check & computer tell no purchase nessasary
Q: change spark plugs on a 1996 toyota camry?
Answer : disconnect battery, remove spark plug cables and boots, and remove old spark plugs. next, put in new spark plugs, replace cables and boots, and reconnect battery.
Q: turn off maintenance required light on a 2006 toyota camry?
Answer : step 1. put key into ignition and turn key to on position, next press trip button to trip a, next turn key off and remove, step 2. put key into ignition and press trip button in while holing turn key to on position, see maintenance required light and odometer blink a times then trip light shut off. and done.
Q: add transmission fluid to a 1991 toyota camry le?
Answer : nelson toyota manin transmission dipstick. best to check level of fluid after being driven at least 15 miles. check fluid level in park.
Q: camry been cranking up but turns on wants got a diagnostic and said ignitor be also gas filter be a problem as well because ignitor cost 400 bucks?
Answer : having same issue on 93 camry - got diagnostic, replaced distributor same problem, another diagnostic, replaced ignitor, having same problem, dies while driving. any new ideas? having same issue too with 1994 camry, 6 clyinder. a mechanic changed fuel pump, mass air sensor. then thought maybe ignitor. so bought one on ebay (i know risky) since getting in deep on issue. anyway ignitor did not fix either. from see here on internet i'm going to check out fuel pressure regulator. say to check vacuum hose comes off top of regulator. if hose gas in then regulator bad. next thing i'm going to check. let know find and please let me know if get any results.
Q: size of speakers in a 96 toyota camry?
Answer : front - 4'' rear - 6'' x 9'' source: have change speakers in 1994 and 1996 toyota camry.
Q: set static timing on a peugeot 106 cam belt failed?
Answer : on a 106 petrol (tu) engine cam shaft be located using a 8 mm bolt slide through cam shaft pulley and into a corresponding hole in cylinder head lock cam shaft in place. crank shaft a little more difficult as need a special or modified tool approx same diameter as a 6mm bolt and long enough to slide through block and into flywheel (approx 50mm), hole located in front of engine (same side as oil filter) on gearbox end of block. (you have to look for as not always easy to see behind dipstick tube). (this hole in same position on diesel models but more difficult to get at) if a diesel model may be worth taking to a specialist as tension of belt affects diesel pump and affect running and starting of engine.(also diesel engines have internal damage after a cam belt failure)
Q: find a fuse box diagram for 1988 toyota camry?
Answer : a person find a fuse box diagram by looking on back of fuse box panel cover. also find a diagram in owners manual of car.
Q: factory brake pads horrible on 2004 toyota camry type of brake pads use to replace them with give more stopping power?
Answer : there tons of great pads out there for toyota camry, as well as a host of braking upgrades and options. as far as an install and forget type of pad, ebc makes some great pads perform better than oem pads and cost a lot less. i've included a links here for to pads and upgrades as well such as: fluid, stainless steel brake lines, performance rotors and even big brake kits. cheers, gpi performance
Q: ac filter located on a 1986 toyota camry?
Answer : there isn't one
Q: dealership turn off check engine light?
Answer : be done at home with a computer reading device ckecks cars computer.they not cheap ,but rent them from most auto parts stores. hello, go to www.harborfreight.com. have a scan tool for about $50-60 of scan for and return check engine code. then erase with a push of a button. an obd-ii reader and works with only 1996 and newer models. alternatively, remove negative battery cable and push brake pedal for about thirty seconds. works as well, however remove radio pre-sets and erase computer's memory so have to re-learn driving habits. code reader simply easier and worth investment, especially if be working on car yourself. good luck. john
Q: turn off maintenance required light on a 2006 camry?
Answer : usually be accomplished by setting trip odometer to current mileage, turn off car completely , push and hold trip button, turn on key without cranking motor and watch lines mileage appears count down till mileage reappears. if doesn't work, set trip to trip a or trip b and try again.
Q: change timing belt on 1998 chevy lumina?
Answer : chevy luminas 3.1 engine not have a timing belt. have a timing chain last well up to 200,000 miles
Q: change out radio on a 2002 toyota camry?
Answer : changing out a camry radioi have done some looking - on both site and - and have come to conclusion way to similar for of earlier 2k's. all answers variations of following: (begin quote of 2000 radio's answer) use a wide blade screwdriver and gently insert between plastic ring (goes around radio and ac controls) and vinyl on dash. then pry ring loose. there about six push in clips hold on. worst of it. rest be obvious. remove 4 bolts and 2 wire harnesses from back. recomend buying an aftermarket wire kit matched new radio to stock harnesses. makes life easier. walmart and parts houses carry them cheap. (end quote) suspect needs to be done this: on 2002 camry, radio and some controls part of a larger assembly, and suspect that, using steps above to pry assembly loose, radio then be removed. in case, a cd appears to be stuck in cd player, so need to remove radio to repair cd mechanism. try later on get a moments, and report results.
Q: thermostat located on a 1992 toyota camry xle v6?
Answer : on both diesel and gasoline engines, thermostat located in water inlet housing connected to lower radiator hose.removal and installation:caution: never open, service or drain radiator or cooling system hot,; serious burns occur from steam and hot coolant. line up jiggle valve with ethel protrusion on housing. position water inlet housing with thermostat over stubs on water pump and install two nuts. tighten 2 nuts to 78 inch lbs. fill coolant system with a good brand of ethylene glycol based coolant. start engine and inspect leaks.
Q: replace driver side mirror for a 1999 camry?
Answer : 1999 camry power mirrorto install mirror, remove interior tweeter plastic housing on door at base of window by inserting a flathead screwdriver down from top, pop out easily. tweeter speaker held in by 2 of 3 nuts hold mirror on car. remove nuts with a 10mm socket wrench. tweeter speaker a couple of inches of cable, set to side. 3rd nut located in door jamb under a rubber cover, remove cover and then nut with 10mm wrench. mirror base attached to outside of car with black weather caulking, rocking old mirror body a times loosen it. interior door panel must be loosened (maybe removed) as cable runs about 4" under panel. there screws under armrest, 2 at base of door panel, one under a tab in door handle, one under a cover a inched below tweeter speaker. all removed with a mid sized phillips screwdriver. mirror power cable goes into door about 4" under plastic weather seal. pull back plastic and unplug power cable. entire old mirror assembly now be removed. insert new mirror and run power cable as old one run and plug in. a good idea to test power to mirror before closing up panel. reverse steps, reseal plastic on door, reinstall door panel making sure panel seats properly into window channel. push ithe mirror into place (seal if a seal not provided way mirror originally sealed against outside of car. tighten 3 nuts to hold on mirror, remember to reinstall tweeter speaker in mirror post. reinstall tweeter cover, pops back into place, hook in bottom and line post up to hole and pop in.
Q: ot mean airflow on an 86 toyota camry barely comes out ac on and air cold?
Answer : malfunctioning blower fans cause air conditioning cold air to not flow properly. airflow vent direction door might be stuck closed.
Q: a oil change person forgot to remove old oil gasket and leak and engine knock cause timing belt to break and perm engine damage?
Answer : if understand ? not changing an old oil filter gasket casue damage to engine no only if leaked out all oil wise no. if filter change cause of leak and lost enough oil for engine to start clattering, yes, caused permanent engine damage.
Q: replace a remote for a 1999 toyota camry factory alarm system without having to pay over 230 from dealer?
Answer : remote a red button,to lock system, black button to open system, and a green button to put on lights. may replace remote without getting a stimullus grant from government.
Q: install a radiator fan?
Answer : ollie collinsdepend car is. most cars have 2 10mm bolts at top of casing and maybe 2 at bottom.then disconnect electrical plug and then lift upwards and outwards. may have to disconnect top radiator hose to get out.
Q: change front speakers on a 1993 toyota camry?
Answer : first have to remove front door panel, whole thing, then unbolt speaker and unplug wires, and put new speaker in...there be screws along outside edge of door panel, underneath cushions on handle..unscrew all of these, then put a screwdriver underneath door latch and try to "pop" out, door panel then come off.
Q: change timing belt on a 1998 accord 4-cylinder?
Answer : honda honda recommends replacing every 105,000 miles or every 10 years whichever comes first. <b>warning:</b> an interference engine. <br>
Q: change back speakers in a 1991 silverado extend cab and 6 by 9 speakers fit?
Answer : not attempt to replace speakers!!! have in back 4x6 inch speakers, and no 6x9 not fit. panels in back speakers are very fragile. basically there no way replace without breaking majority of tabs or panel itself. one part of car cannot be messed with unless have some replacement panels. assure you, break them. even if try to get done professionaly, havent seen any installers touch them unless got replacement panels. dont need to replace them anyway, get a good set in front. not worth to dive into that. wondering myself. went to a local electronics shop, and have speakers in back listed as 4x6.. there be room for 6x9 but some modding have to be done. hope helps
Q: to change a headlight on a 2003 mazda?
Answer : bulb located under hood jump behind lamp. all have to twist plastic right to left and uncrew it. electric have a clip on pop off directly on rear of exsisting bulb. unplug, and pull out of headlamp. place new one in plug, and you're set to place backin screwing plastic "o" cap over to secure in place.
Q: replace driver's side drive axle on a 2002 ford focus?
Answer : easy jobyou got to get car up and take tire off. there a main nut right in middle of rotor. socket you'll need a 1 1/8m- 1 1/4mdepending on transmission. nut holds axle to rotor. sometimes easier to remove nut holding tie rod end, and ball joint nut, both located right behind rotor. ball joint nut a allen key bolt and a 13m or 15m size nut. once bolts removed rotor spindle assembly be open to play so pull on to push axle out of rotor spindle assembly. from there pull axle out of tran. may want to carefully pry axle out from trans. a good idea to replace th e axle seal located at opening in trans. black. replacement a reverse. always follow torque spec get from any haynes manual. autozone.
Q: a 1990 toyota camry start but then lose power but restart after sitting a minutes?
Answer : sounds like a fuel problem to me ,if not electrical .this be linked to a fuel fuse in fuse box or a filter problem ,or even perhaps a fuel pump. start to check flow at engine , by disconnecting at fuel injection.then turn on key to start position.put a hose on line and make sure going in a container,check flow and also pressure .if got good flow and presure and still nt run go back to all electrical points .and also check for loose wires around distributor.
Q: timing marks for 1989 toyota camry?
Answer : timing marks 1993 yoyota camry 2200
Q: fuse controls power windows in a 1992 camry?
Answer : a short in power window harness on driver's side and found answer online so i'll pass on. there a pal fuse controls power windows located directly under steering wheel. remove panel under steering wheel and see among things a black plastic vent passes up to vent to left of steering wheel. to be pulled away but enough to get to fuse. on left end of vent a black plastic "button" looking clip pop out with a screw driver. now vent pull out and away but try to keep connected at right end so don't have to mess with reconnecting too. as pull vent out, see pal fuses in a box. don't remember for sure one but believe pink one on right. take a flash light and be able to look into window on top of fuse and see if blown. fuses pull out and a breeze to replace. all may sound difficult but really not and only takes a minutes. went to a local junkyard and practiced on cars and then tried on car. actually took pal fuses from junk car and used them in mine.
Q: find a diagram of fuse box cover on a 1996 isuzu rodeo?
Answer : simply logon to /www.myisuzuparts.com/index.php
Q: fix brake lights on a toyota camry?
Answer : easy, baby! open trunk, and look behind brake lights are. there be a removable panel over area. pop off, and you'll see back (sockets) of brake lights. simply unscrew old burned out bulb and replace gently with a new bulb purchased from an auto supply store. don't tounch glass bulb part of new bulb as you're installing it. viola.
Q: remove a rear brake drum from a 1993 toyota corolla?
Answer : fully retract brake adjuster and strike outer side of drum with a big hammer new answer headline for earlier models, e.g. 1989 station wagon (estate), answer to have handbrake off, jack up rear wheel, remove wheel, pry off cap from wheel nut (using a flat screwdriver), remove wheel nut (remove locking pin, nut), and slide off whole drum and wheel bearing. no hammering needed at all.
Q: add transmission fluid to a 1998 toyota camry?
Answer : pull out transmission fluid dipstick. use a small thin funnel and add right through place dipstick came out of. make sure getting transmission dipstick and not engine oil dipstick. use only toyota transmission fluid (available at dealer or irontoad.com) as not all types compatible. engine be warmed up, and running at idle on level ground to check fluid level. not overfill or foam and then have real big problems. dipstick have two readings, cold and hot. transmission not necessarily hot engine is. to warm up transmission, drive for about 30 minutes.
Q: ignition coil located on a 1990 toyota camry wagon?
Answer : under distributor cap. black and held to distributor with 4 phillips screws. there 2 studs for control wires.
Q: drain automatic transmission on a camry 2003 also need to know qts of fluid and type needed?
Answer : there a drain plug in transmission pan. takes a 10mm allen wrench to remove it. once removed wait until only little fluid left dripping (maybe a drop every second or two). reinstall plug, then remove transmission dipstick. put a suitable funnel in dipstick tube and add 3q type t-iv fluid. start car and check level, if low, add until level between "hot" and "cool" marks. 4 quarts usually sufficient, sometimes a little more necessary.
Q: change timing belt on a 1989 toyota camry?
Answer : if asking question, there a good chance don't have extended knowledge to handle this. then be left to a professional. however if intent on doing job yourself retain a manual such as a chiltons. be ally and pay close attention to timing marks determine whether or not itll run again. toyota forgiving however because most of engines non interference and not break if don't line up marks properly.
Q: - toyota 2000 camry battery removed and radio asking for code help?
Answer : if battery removed and radio asking for code then must contact toyota dealer. there a code installed from factory may be able to help with. also get fixed read owners manual on to change radio code to one remember.
Q: cost to have rear struts completely replaced on a 1997 4 cylinder toyota camry?
Answer : camry struts expensive installedi have a 1995 toyota camry and have quotes of $800 to $900 per axle. havn't replaced them yet, but bushings on rear struts rattling. have 139,000 miles on camry. $1,800 seems like a lot of money to spend on a car worth maybe $3,000. only be $172 toyota rear strut each and then $110 labor each strut...check out discount tire as even have buy 3 get one free today for both front/rear purchase oct2009 lasts till 10/18 only.
Q: change a dim gear indicator light on a 2000 ford contour?
Answer : pop off cover using a small flat head screwdriver, slide up shifter an inch or two. be able to feel bulb slides in. pull bulb out and replace.
Q: turn off maintenance required light after changing oil on a toyota corolla?
Answer : 2008 toyota corolla?"answer year ?
Q: remove factory radiocassett player from a toyota celica 89 model?
Answer : take off bottom part of dash take ash tray out and glove box then bolts on middle console and come out.
Q: change high mount brake light in a 1994 toyota camry?
Answer : here's to access high mount stop light on a 1996 or 1994 toyota camry sedan. readers have reported works on some related models and years too. first of all, define "forward" to mean direction car moves you're driving forward. won't need any tools, a new 921 bulb and hands. all work be done from back seat. flexible plastic cover held in place by two hooks, each of keeps cover from moving up or forward. hooks molded onto forward part of cover, but on inside so one can't see them until cover removed. (unfortunately, makes really difficult to "figure out" to remove cover!) vertically, hooks centered on forward part of cover, and horizontally each located 1/3 in from edges of forward part of cover. put thumbs on forward part of cover and push hard; need to deform plastic away from about 1/4 inch in order to release hooks. not hear or feel hooks release. while still pushing, start moving cover up. then slide cover along glass of rear windshield to remove it. reflector unlocks by gently lifting up on two plastic tabs on top while pulling top of reflector towards you. lift reflector out. remove bulb by sliding straight up. hope solves for you! riick
Q: change battery on a 1992 toyota camry?
Answer : disconnect battery cables. find battery clamp and remove it. lift battery out, then set then new one in place. install clamp, then connect battery cables.
Q: cabin air filter for a 1999 toyota corolla?
Answer : have a 1999 (le) and not have one behind gloves box. once open gloves box; find two screws .
Q: change headlight bulb on a 2002 toyota camry?
Answer : theres a white or red piece of plastic behind headlight (you have to open hood and reach hand in behind headlight) holds light in and also electrical connector...you grab piece and twist hard to left and only turn about 1/4 or a 1/2 of a turn and then pull straight out. you'll have to push on release on plastic connector to get bulb out, but then pull right out of socket. push new one in until clicks and put white piece with bulb into slot and turn to right about 1/4 or 1/2 turn until clicks.
Q: replace seat belts in a camry?
Answer : isn't something most people answer. need to check owner's manual or a car repair manual. be sure doing job correctly because incorrect installation lead to death or injury.
Q: kind oil use for 1986 toyota camry?
Answer : 1996toyota camry 20w50 best choice for old of a car. have driven older cars and weight lubricates engine great! even have mechanic put in van oil change time comes. correct oil to use. car calls for 10w-30, 20w-50 be used only if extremely high mileage on car. an trying to put off rebuilding engine for a time. also 20w-50 lower mpg's.
Q: complete driver's side headlight assembly on a 1990 celica st replaced?
Answer : if need 1 .i have 1 for sale.
Q: get a rear bumper for a 1998 pathfinder 4x4?
Answer : junkyard
Q: toyota camry radio fully functioning; however there no sound there a specific speaker fuse and located?
Answer : someone answered: if there no sound, then did say radio fully fuctional???????????? reality though, if a speaker wire shorted radio appear to function in every respect but no sound emit from any speakers. happened to me too, with an '87 camry, new radio, all speakers checked-out, massive frustration... solution: wiring guides call for joining "green" wire on toyota to grey wire on new radio... don't tell there two green wires. hooked up "greenest" wire by using dark green... ...use light green wire for right front speaker (+) and might solve problem, worked for us!
Q: fix control panel illumination lights on a 1996 mercedes benz e 320?
Answer : instrument panel in almost all benz if not all removed by simply pulling out from front. held in place by a tight fit inside dash board.on 1999 e320 manufacturer recommended deactivating airg bag system first. to protect self from an accidental deployment of air bag while working on dash.i able to remove instrument panel without deactivating air bag so decide to in respect.now, manufacturer sells a simple tool for removing instrument panel nothing more than two simple hard wires like ones for hanging clothes. cut ends of wire so straight and smooth. then put a bend in form of an "l" shape at one end of wire about 1/4" long.first try pulling instrument panel with hands only, may be able to remove using hans only. if not come out completely by hand, then insert "l" end of wires at each end of panel and engage ends to back of outer walls of panel and continue pulling with wires but being carefull not to damage it.replace any burned out lamps and replace panel by simply pushing back in place until fully seated.good luck. ed rivera
Q: air filter located on a 2001 volkswagen passat v6 and change it?
Answer : have a 1999 and air filter all way on upper left hand side after open hood, remove plastic and big vacuum looking hose, see housing for air filter. a huge pain, clamps really tight and better off paying to get done. usually costs less than air filter itself if bought yourself. http://www.tobio.info/passat/howtos/passat_air_filter.html
Q: change rear deck speakers in a 2000 toyota camry?
Answer : have to remove package tray w/ seatbelt clip tops, etc first. try to use toyota speaker adapter plugs so don't need to cut wires and mess electric system up. get them from ebay or amazon.
Q: check error codes on a 1988 cadillac?
Answer : on most 1988 cadillacs, turn key on and on climate control panel, hold both off and warmer for a seconds. screen flash up codes as a series of letter + 3 number codes, indicating each as either current or history, ending with a menu entry (usually "ecm?"). to reset codes, press fan-lo button to change display until reads "ecm?," then press fan-hi; cycle with fan-lo until see ecm clear codes? and press fan-hi again. then tap off button twice and cycle through first menu with fan-lo until reads bcm? and hit fan-hi; again, cycle with fan-lo to bcm clear codes? and press fan-hi. to exit menus and restore normal displays, tap off until reach main menu, then tap off button 3-4 times rapidly. (or, turn off key or start motor, either restore display.) on diagnostic plug under center of dash, use a jumper wire to short lower two right hand connectors together after check engine light come on and car running. check engine light then flash codes as: flash flash flash pause flash flash flash flash long pause - be a code 34, each code flash 3 times before moving on to next code and after last code, start over with first code. then have to look up code to find problem behind
Q: find power steering fluid cap on vehicle?
Answer : compleatly depends on car. need to list make,model and year for question to be answered. include engine size also plz. read manual or ask a mechanic
Q: plug and spark plug firing order tor a 1989 toyota camry v6?
Answer : firing order 1-2-3-4-5-6. see http://autorepair.about.com/library/firing_orders/bl-toyota-firing-89.htm. note distributor turns counterclockwise.
Q: replace center brake light in a toyota camry?
Answer : found answer earlier at site, and worked! trick to disengage plastic catches about 1.25" from sides of high brake light on rear deck of 1994 camry sedan (4 door). forcibly push in on unseen catches while pulling on rest of housing toward front of car. once off, reflector centered in assembly. reflector also two catches to be aware of, but visible. once reflector off, light bulb lifts straight up to get out. no tools required, bulb. baxter auto parts in tigard, or wagner bp921 two packs of bulbs. worked on first test.
Q: cause window to roll up and down warm outside but not cold and fix on a 1994 nissan altima?
Answer : problem typically in driver's side master power window switch. in most cases be easily fixed by removing switch, unclipping switch in middle to pull apart and cleaning contacts with alcohol. 1) insert fine tipped screwdriver into highest part of switch and pry away from mounted. pull switch upwards and disconnect 2 or 3 push-in connectors. come out easily once smash in connector tab on top of each one. 2) take switch to a table to work on it. upside-down, see 3-4 small squares with plastic clips on inside of them. insert screwdriver between upper and lower plasctic housing to separate clips from one side, then other. give access to inside of switch. most switches have springs and connectors fall out, but switch not. a large rubber pad and operates more like a calculator by smashing down rubber buttons to make contact. 3) remove rubber pad, making note of direction go back on. if put back upside down, nothing work. take a paper towel or q-tip and clean both sides of connections thoroughly with alcohol, or another quick drying solvent. not and oil like wd-40. probably see a small amount of moisture and problem comes from. 4) reverse procedure and reinstall switch and be back in business. have done in 3 different vehicles, and worked every time. there still a chance there moisture in switch of door window rolls up or down on, so may have to go a little further and remove individual switch too, but not normally. good luck! original answer: wire expands hot and contracts cold. dust makes problem worse. try spraying potentiometer cleaner... or electronic tuner cleaner (*** not wd-40***) into window controls on drivers side. if know , or mechanically inclined; pull module out carefully and wiggle and clean contacts from under side. good luck!! <br> happened to me morning. have a 1998 altima. tempted to drive to auto-body shop, but used blackberry and googled first. no idea a potentiometer cleaner was. ran in house looking for compressed air, but didn't have any. found a of static guard and figured worth a shot. sprayed window controls and then jiggled switch a bit. 5mins later gave a try and worked like a charm.
Q: replace a heater core on a 1991 camry wac or insane to try for a backyard mechanic?
Answer : to fix 92 camary heater core
Q: turn off check engine light off in 2002 crv?
Answer : "check engine" usually means computer stored a diagnostic code. use a code scanner to find information about stored code.
Q: 2003 toyota camry speaker covers?
Answer : according to dealer can't replace covers, have to replace whole back panel between back seat and window. (approx. a $400 job) :( update: a problem with 2003 - 2005 toyota camrys. (go to http://www.topix.com/forum/autos/toyota-camry and read "rear speaker covers" topic to see at least 78 people having problem.) see some photos of problem here www.camryspeakercovers.com. a technical service bulletin been issued for replacing speaker covers (bulletin #bo019-07). parts cost estimated at $25.00 but dealers seem to be charging from $100 - $200 for service to replace covers. a call to toyota customer service may help persude them to issue a recall. toyota customer assistance center: 1-800-331-4331 tsb(technical service bulletin): bo 019-07 estimated part cost:$25 for pair for speaker covers.
Q: to change headlights?
Answer : watch video. even though it's for vw jetta, but give a better idea. http://www.carpart4u.com/autopart/projector-headlight-volkswagen-jetta-99-05-sp-11.html
Q: fuse box on a 1997 toyota camry for dash lights?
Answer : fuse box located under steering wheel. have to use a phillips screwdriver to remove bottom-most plastic panel - have three screws, one hidden under hood latch and one hidden under panel goes down left side to floor (remove it, too). really have to tug to get plastic cover off, but down there. there be a fuse called "dbd" for dashboard. on back of change drawer a fuse diagram.
Q: to shut off 2005 camry maintenance required light?
Answer : called dealer. it's a quick sequence of steps. turn key on, but don't start engine. push odometer button so on odometer, not trip1 or trip2. turn key off. push and hold odometer button and turn on key, don't start engine. flash a dash a times and then reset maint reqd light. it's easy know how!
Q: happens lose power steering and brakes on a 98 dodge 2500 diesel?
Answer : probably slam in back of some old lady stoped at a red light. caused by a vacume failure, a rebuild kit available try to find a link for one.
