Toyota Camry
Q: egr valve on a 2000 toyota camry i4?
Answer : egr valve a round "valve" (has one hose coming from top, one from side) on top of throttle body. actually, bolted with two bolts to rear of throttle body. if don't know a throttle body is, look for pulley moves press gas pedal (with engine off). answer if remember correctly....there no egr valve on a 2000 camry. if there however be last guy said. answer link below to a picture of egr valve for a 2000 camry 4-cyl. engine with an automatic transmission. bolted to back side of intake manifold with two bolts, and to a flange at top of a steel tube running up from exhaust system with another two bolts. http://catalog.autohausaz.com/autohausaz/image.jsp?title=egr%20valve&url=http%3a//img.eautopartscatalog.com/liveb7010168929oes.jpg
Q: thermostat located and replace located on a 1990 toyota camry 3s-fe 4 cylinder?
Answer : aswer on model thermostat be found by following lower radiator hose to attaches to engine. hose typically attached to a fitting behind a gasket and thermostat. gasket needs to be replaced thermostat replaced. general procedure: make sure engine cool. loosen hose clamp lower radiator hose attaches to engine - pull forward. place clean pan under hose to catch coolant might spill out. pull hose off. catch coolant in pan. remove bolts on fitting hose attached to. remove gasket. remove thermostat (note positioned and side facing out before removing -- there may be an alignment notch). install new thermostat (the way original sitting,with little "barbell" at 12:00) and gasket. re-attach hose fitting w/bolts. re-attach hose and clamp. put coolant spilled out back in radiator. start engine and allow to warm up and check for leaks. note - if need to remove alternator so as to access nuts holding thermostat cover remember to disconnect battery before removing alternator leads to prevent shorting. good post on parts location and repair procedure. only thing i'd like to add antifreeze a limited life before loses it's ph balance and turn acidic or base, either one cause corrosion in cooling system. loss of additives also cause cooling system to start acting as a ground conductor damage cooling system. there different ideas on to change, try to change mine every 3 years or 24k miles. if want there test strips to check ph balance, protection temp and phosphate levels (prevent oxygen molecules from collecting around cylinder liners and etching them - usually more problematic on diesels). hth, dave
Q: drivers side drive shaft come out of transaxle on a 1990 toyota camry 3sfe with 5-speed manual transmission?
Answer : if camry anything like mr2, procedure requires a brass chisel, if remember correctly. remember not pull on half shaft as cause interior u-joint thing to separate and spill white lithium grease everywhere... strongly suggest acquiring a factory service manual or seeking assistance of someone completed task before attempting to remove drive shaft. learned hard way on mr2... .
Q: remove ball joint on a 96 toyota camry le?
Answer : 1996 camry ball joint removal 1. jack car up , put on safety stands, etc., etc. 2. unlock steering so manipulate wheel hub / spindle assembly as needed. 3. remove wheel. 4. on bottom of spindle & attached to lower control arm ball joint. 5. first remove cotter pin from castellated nut on ball joint. may have to clean to find it. ( soak good with some pb blaster or penetrating lubricant at stage) 6. loosen castellated nut. (you not be able to get nut completely off at stage because blocked by cv joint) be a 17mm - you'll need good quality open end wrench to prevent rounding off nut. (once nut loose, work back and forth to get penetrating oil into threads so easier to deal with) 7. on bottom of control arm 2 nuts need to be removed, and a third on top of control arm. (on some vehicles may be rivets need to be drilled or ground off) 8. once have control arm disconnected from ball joint be able to get ball joint loose from spindle. - use a ball joint fork, goes between top of ball joint boot and bottom of spindle and struck on end with a hammer. or - use a ball peen hammer to strike side of spindle ball joint bolt passes through spindle. 9.the ball joint drop. 10.now remove castellated nut. find a pair of needle nose vise grips useful for holding tapered shank of ball joint bolt so doesn't turn while removing nut. 11. install new ball joint into lower control arm first. hint. a large pry bar inserted into one of holes towards rear of lower control arm allow to push lower control arm down far enough manuever spindle assembly into place over ball joint bolt so pops into hole more easily. following statement here before edit, so heed if like, but an alignment not necessary, due to fact ball joint not an adjustable front-end geometry point. all replacement ball joints be made to same specification. never hurt, but not an absolute need. *after replacing ball joint need to get a front end alignment because have altered suspension geometry with a new component.*
Q: timing marks on cam and crank located on a toyota camry 4cl 2.0?
Answer : cam mark behind pulley on oil seal plate towards top of seal looks like a small line indentation. rotate pulley clockwise until see well then take yellow model paint and brush a little into dent. now find hole that's in one of spokes on pulley. turning pulley clockwise line hole up with timing mark be able to look through hole and see yellow timing mark. heres tricky part can't look through and see because theres a fender in way if don't have engine out. use a telescoping mirror and a flashlight put mirror down in there facing hole with angle so see it, shine flashlight into mirror reflect and show inside of hole. turn pulley until see yellow mark lined up with hole in pulley spoke. crank a little more tricky there a mark on back edge of pulley. turning clockwise line up with 0 mark on belt housing cover, but prefer to pull spark plug in #1 cylinder closest cylinder to timing belt and put a 2 foot wooden dowel down into it. then turn crank with a strap wrench until piston reaches tdc "top dead center" point wooden dowel reaches it's highest point before dropping back down. remember turn clockwise.i went through misery with a 1991 3sfe trying to time cam. there 4 deep cuts in camshaft bearing cap, one round mark in cap lines up perfectly with timing hole, and then there small cut(i think triangular),in edge of cap correct timing mark. not use circular mark at about 9 o'clock. correct mark appears at about 11:00 o'clock but in reality at 12:00 on engine because engine mounts at a slight angle in camry. engine extremely sensitive to timing setting. miss by one tooth on then belt and may not start. be sure to turn crank a couple of times clockwise and check cam again after initial belt install to be sure haven't taken up some slack from wrong side upon release of tensioner.
Q: replace water pump on a 1996 toyota camry 4 cylinder 2.2l?
Answer : 4is 4 or 6 cylinder ? a 4 cylinder
Q: replace alternator on a 1989 toyota camry?
Answer : it's simple but a little hard getting back in place because of belt. take two people. use a socket wrench if not in too tight, otherwise you'll need an impact socket wrench. first remove small bolt on top (it have an obvious cover easily removed.) then lossen bolt right in front attached to a brace. there also a pin-like bolt on side of alternator towards top (right by belt). there may be another bolt on right side, but don't recall. finish removing front bolt and then work pin in back out. once pin out may have to tug a bit to get alternator out because it's usually in pretty tight. that's it. ready to replace it, need to loop belt back over pulley and make sure lined up on two pulleys below. need someone to push alternator up to keep in place while put bolts back in. difficult because belt tight (or be!). used an old axe handle underneath to get leverage needed. be sure don't let handle or leverage tool rest on radiator or might cause damage. shouldn't take more than 15 minutes to take out and about to put back in.<ul><li>to replace alternator:</li></ul> -disconnect negative battery cable; -unplug 3 wire connection on back side of unit; -carefully pop up plastic cover on b terminal, remove nut using 10 mm wrench, and lift ring connector from stud; -break loose pivot bolt using 14 mm socket and flex-bar; -loosen tensioning bracket bolt 14 mm; -loosen 12 mm locking bolt(horizontal one); -remove 12 mm tensioner bot(vertical, long one); -push alternator down and slip belt off pulley ; _completely remove pivot and locking bolts; pull alternator out of mounting bracket, if necessary,gently pry between bracket and alternator. installation in reverse order. use tensioner bolt to adjust drive belt tension.torque bolts to 18 lb*ft
Q: turn off maintenance service light on a 2004 toyota camry 4 cylinder?
Answer : maintenance light <ol><li> turn car on -- make sure see odometer -- not "trip meter" but actual mileage odometer. </li><li> turn car off. press odometer button down, while turn car on. numbers turn into "--" one by one until all gone. then reset.</li></ol>
Q: aim headlights on a 1995 toyota camry?
Answer : 1992-1996 toyota camry headlight adjustmthere two screws affect headlight alignment. one faces up on nearest fender verticle adjuster. one one side next to grill horizontal adjuster.
Q: cause a toyota camry to hesitate taking off and act like wants to die?
Answer : i'm obviously not only one. gettin camry 94 checked out at moment. toyota computer didn't show any reading out of range so don't want to deal with problem unless wallet fit. with mine completely random. at toyota said a case like before but a constant lack of power. solved by replacing actual distributer (not cap or rotor but electronic component). it's to expensive to give a try though. have fun! spent a fortune chasing a cold start plus engine heat up time, low engine rpm stalling issue happened in wet weather in a 87 camry? seemed like once choke equivalent function stopped engine couldn't cope and only run if kept above 2000 rpm. no expert find cause simple. new plugs! must have a humidity prone short - perhaps a result of spark plug layout.
Q: replace thermostat located on a 1999 dodge intrepid?
Answer : on 2.7 and 3.2 engines, thermostat located at end of lower radiator hose, behind power steering pump. involves draining coolant, removal of lower hose and the thermostat attached to it. on 3.2l engines, have to remove oil filter as well. there a heater hose attached to thermostat housing at block to be removed also. a 2 inch long piece of rubber hose, and loosen clamp on one side of it. once have both hoses off, remove thermostat housing, and thermostat. 2 bolts with 10mm heads. make sure replace gasket and clean surface. not common for thermostat to go bad on cars so check water pump if have a 2.7l engine, and inspect rest of system to make sure there no problems elsewhere/. real life note -- if noticing dripping on ground safely lift car and inspect underside. if coolant coming out a small hole (weep hole) next to thermostat housing, means water pump leaking and needs to be brought to a mechanic. (major job involving lots of work and removal of many parts - not job for weekend mechanic sorry) on hand if see coolant dripping from thermostat housing that's a $30.00 fix. replace gasket and buy a new thermostat since got apart. 2001 dodge intrepid water pump went bad at 51000 miles and gasket started leaking at 70000 miles. water pump cost me $500.00 - gasket myself. if want to make yourself feel better most likely intrepid paid for by now and $500.00 for a fix a new car payment on a decent car. if have to put $500.00 in car now to fix it.- heck paid for.
Q: get key out of ignition on a 1989 grand prix key not come all way back to off position?
Answer : according to sources have found in researching question on web .. problem most likely shift lever assembly. from msn site:"an occasional problem with vehicle shift lever assembly (transmission shift lock actuator), automatic transmission only, and ignition lock cylinder assembly. a failure of shift lever assembly prevent ignition key from being removed from ignition lock cylinder. failure of ignition lock cylinder may prevent vehicle from starting. cost to repair shift lever assembly estimated at $73.00 for parts and $71.50 for labor. cost to repair ignition lock cylinder estimated tat $21.54 for parts and $39.00 for labor. all prices estimated at $65.00 per flat rate hour and not include diagnostic time and applicable taxes.
Q: change front right signal flash light bulb for a 1997 honda civic ex sedan?
Answer : easist way to partially remove wheel house liner and stick hand through there. there be 4 push clips remove with a small regular screwdriver. pry out center part and then remove whole push clip. at point pull down on plastic liner and reach through to light socket. good lcuk.
Q: change oil on a 1997 toyota camry?
Answer : allow vehicle to cool.engage parking brake and place wheel chocks behind rear wheels.raise front of vehicle.place jack stand under vehicle.lower vehicle until jack stands supporting vehicle.make sure vehicle safe to go underneath.place a oil drain pan under oil pan.use a 6 point 14mm wrench or socket to remove oil pan drain bolt.turn bolt to left until bolt loose.remove bolt,allow oil to drain.check drain plug threads and gasket.clean drain plug and area drain plug screws into pan with a clean shop towel.screw drain plug into pan and tighten bolt with wrench or socket.get tight,but not over tighten.open hood.locate oil filter,sholud be on front side of engine,directly in middle.place oil drain pan directly below filter.remove filter with a small oil filter wrench.examine area old oil filter mounted.make sure there not an old 'o' ring left on oil filter mounting surface.clean mounting surface.open a bottle of oil,pour a drop of oil on finger.rub oil on 'o' ring of new oil filter.screw oil filter on mounting area.tighten oil filter by hand.get tight.remove oil filler cap,pour in 4 quarts of 5w 30 oil.start vehicle,oil light go out within 5 seconds.look under vehicle,inspect oil drain plug for leaks.check oil filter area for leaks.listen for rattling and knocking.lift vevicle,remove jack stands and wheel chocks.while under hood check power steering,brake,windshield wiper and transmission fluid.inspect air filter and check air in tires(30-32psi).take used oil to a qiuck lube shop(jiffy lube).a lot of words,simple to do.take time. agree. 1997-2001 camry's easiest cars to change oil i've ever seen. highly disappointed with new camry's oil location. however, new-style lexus es300 oil filter location in a similar location as 97 camry (just under manifold) and provides easy access without having to put car up on ramps.
Q: reset a check engine light on a 1996 toyota camry le?
Answer : first, if something like a loose gas cap, tighten and reset itself in next 100 miles or so. if something else, like a leaky gas cap never reset. but to reset onboarddiagnostic (obd)computer... go to ebay and search "obdii" and buy one, run about $50.00 including shipping. there two types, iso for chrysler and some japanese, and one for all like ford and gm. there several both, kind want. be sure to email ebay seller and ask if used with year and model. (1996 a changeover year for obdii technology, so advice may not apply to everybody--but dealer service guy tell over phone--ask him if obdii compliant.) get it, plug in and let cycle 4 or 5 times and resets everything. then have to drive car for 50 to 100 miles for onboard computer to test everything, and in meantime car fail smog checks because no history in computer and smog test procedure demands a history even if there no pollution. cut and paste http://search.ebay.com/obdii for a list of them for sale on ebay. most units come with a list of generic fault codes so tell problem is, be helpful.
Q: find and replace small light bulbs in 1987 toyota tercel wagon instrument panel?
Answer : take gauge cluster out otf dash. on back there black plastic caps flat on two sides so grab them. twist one way and then pull out. pull bulb out and push new one in.
Q: reset check engine light on a 1996 toyota camry?
Answer : go to ebay and search "obdii" and buy one, run about $50.00 including shipping. there two types, iso for chrysler and some japanese, and one for all like ford and gm. there several both, kind want. be sure to email ebay seller and ask if used with year and model. (1996 a changeover year for obdii technology, so advice may not apply to you--but toyota dealer service guy tell over phone--ask him if obdii compliant.) get it, plug in and let cycle 4 or 5 times and resets everything. then have to drive car for 50 to 100 miles for onboard computer to test everything, and in meantime car fail smog checks because no history in computer and smog test procedure demands a history even if there no pollution. cut and paste http://search.ebay.com/obdii for a list of them for sale on ebay. go to ebay and search "obdii" and buy one, run about $50.00 including shipping. there two types, iso for chrysler and some japanese, and one for all like ford and gm. there several both, kind want. be sure to email ebay seller and ask if used with year and model. (1996 a changeover year for obdii technology, so advice may not apply to you--but toyota dealer service guy tell over phone--ask him if obdii compliant.) get it, plug in and let cycle 4 or 5 times and resets everything. then have to drive car for 50 to 100 miles for onboard computer to test everything, and in meantime car fail smog checks because no history in computer and smog test procedure demands a history even if there no pollution. cut and paste http://search.ebay.com/obdii for a list of them for sale on ebay.
Q: hard to change egr valve on a 97 tahoe and there anythings may need to be concerned about?
Answer : passible egr needs cleaning only. take off and clean carbon from and mounts. check wiring and vacuum to also. if still doesn't work, replace it. 3 inch round thing at rear of engine.
Q: replace a driver's side speaker on 1997 toyota camry?
Answer : cruthfeild website only an ad page --> go to www.cruthfeild.com get install info and buy new speakers if don't know to remove inside door panel, link helpful: http://autorepair.about.com/od/otherodddiyjobs/l/aa092504a.htm. in addition to advice at above site, found another trick to removing trim around inside door handle. above article refers to putting a screwdriver under door handle and pushing down ... to release a "secret latch". that's first step. second step (which not in article) to insert scredriver above door handle ... vertically above spot in above article. then gently press screwdriver handle down. with screwdriver acting as a lever, tip of screwdriver push up on top part of trim. lift trim up off a small pin on handle mechanism. with both bottom and top of trim piece now "unlatched", slide trim toward back of car, while open inside door handle (as mentioned in article). trim come right off. be sure to slide trim toward back of car, as move trim away from door panel. (there a "hooked" piece of plastic on back of trim prevents from pulling out perpendicular to door panel.) 'hope fine points help. ps. 1996 camry 2 screws on bottom of door also holding interior door panel in place. wasn�t in article.
Q: replace bulb for instrument panel lights on a '92 chevy corsica?
Answer : there three little screws under headlight switch/knob thing, and three screws under wiper control knob/switch thingy... take out. place both hands on top of dash and pull towards you, and pop off... not be afraid to pull... ok, then unplug wires to headlight switch, and then same to two plugs connected to wipers. set dash on passenger seat for now... ok! step one! easy! now need to take out black, (not gold) screws, and pull out instrument panel, also don't be afraid to give a nice tug too,... now, with panel in hands, flip over backside and marvel cool looks... then find 4(i think)light bulbs!!! there one indented in center, one to right, one to left... about 1/2 in. wide and round... now... realized that not problem... bulbs not burnt out... check fuses (drivers side, with door open, inside dash, with a cover says 'fuses' on :)... did ages ago... as said #15 or something instrument panel (3 watts) turned out to be s.i.r fuse.
Q: change brakes and rotors on a 1997 toyota camry 4 cylinder?
Answer : doesn't anyone believe in going to library to look at a manual? there a difference between rear drum brakes and front disc brakes. if didn't wait until brakes down to steel backing plates, need to replace rotors? even if have normal wear don't need to be replaced - don't even need to be turned. disc brakes a piece of cake - use a big screwdriver to push caliper pistons back (make sure didn't add brake fluid as level dropped because may overflow push back piston), take out a couple of bolts to pull off caliper, knock out retaining pins, pull out old pads - put in new pads... and 15 minutes later, you're done. back drum brakes be good for about 100k... they're a pain to change if don't have tools (worse case a visegrip works) and cost three times as much, but everyone makes a big deal out of disc brakes and charges whatever get away with. good advise above. on disc, use ceramics (won't squeal, last longer) and not lose seemingly useless small v-shaped wire tension clips if included in assembly.
Q: replace outside driver's side door handle on a 1995 chevrolet beretta?
Answer : open door, on inside of door (the part door striker/latch is) there's bolts remove. seems to me there's a panel runs along there as well have to remove. old handle broke so pulled remains out from inside of door. start by removing panel on door frame, and look for it's bolts. buy a haynes manual if you're still confused.
Q: remove rear door panel on toyota sienna 2000?
Answer : lower panel held on with push on clips, 11 of them be "gently pried up" according to service manual. remove handle and strap prior to removal.
Q: replace thermostat located on a 1988 mazda 626 4 cylinder automatic?
Answer : check autozone.com 2.0l engine disconnect negative battery cable. drain engine coolant from radiator to below level of thermostat. fig. 3: to remove thermostat, first drain cooling system, then remove radiator hose-to-thermostat housing cover clamp ... fig. 4: ... by sliding back on hose. note alignment marks on hose and housing cover (arrows) fig. 5: disconnect hose from thermostat housing cover fig. 6: loosen thermostat housing cover attaching bolts ... fig. 7: ... then remove them ... fig. 8: ... along with housing cover/water outlet fig. 9: remove thermostat from housing by simply pulling outward fig. 10: installing new thermostat, note tab (arrow) seats into a notch in housing. jiggle pin must face straight up disconnect lower radiator hose from engine. remove housing bolts, thermostat housing, thermostat and gasket. not pry housing off. to install: clean thermostat housing and cylinder head mating surfaces. make sure thermostat jiggle pin aligned with gasket projection. install thermostat to housing. align gasket projection with opening in housing. spring side of thermostat face into housing. install thermostat housing cover and tighten both bolts to 14-19 ft. lbs. (19-25 nm). fill cooling system. connect negative battery cable, start engine and check for leaks. check coolant level and add coolant, as necessary. for pictures go to: http://www.autozone.com/servlet/uibroker?forwardpage=/az/cds/en_us/0900823d/80/14/44/e4/0900823d801444e4.jsp
Q: turn off a 1998 toyota camery lxe check light?
Answer : disconnnect battery cable for about 2 minutes my 2 cents " check engine light" by far one of most misunderstood technological advances a warning light illuminated there a problem affecting emissions of vehicle.. don't let bother as a good thing once understand it. one point brought up a recent meeting of technicians amount of hydrocarbons greater gas cap left off than engine running. hydrocarbons part of pollution emitted as gasoline evaporates. going a step farther, one facet of emission system "evaporative" portion. fumes from gasoline leaking from system into outside air. one part of emission system trigger a check engine light. say a small percentage of vehicles have a check engine light result of a loose or inadequate gas cap. but understand scenarios possible with "check engine light" vehicle's powertrain computer (note some vehicles have multiple computers aside from powertain computer) run a series of self-tests. only run under certain criteria. and different from manufacturer to manufacturer. some self-tests or �monitors� not run until preceding ones have run successfully. so if there a problem in one particular area preventing another self test from running, have a situation one problem fixed, but another still exists. if fix a problem and drive car through a drive cycle sets monitor (or self test) light go off as passes criteria triggered in first place. there different sources for light to come on. anything caused combustion to fail, commonly called a misfire set light. various sensors such as oxygen sensors evaluate exhaust before and after gases burned in converter. transmission codes may set check engine light to appear. if car running okay, get fixed in a reasonable amount of time such as within month. probably save fuel if do. however if check engine light flashing, be driving as damage being done to converter. some emission components covered beyond standard warranty. converter for example covered up to 80,000 miles by manufacturer. after 1996, auto industry went to a idea called obd ii (on board diagnostics). to get all manufacturers onto a similar plane for troubleshooting and powertrain control. while still differ, corrections and adaptations made for technicians to better fix check engine light problems. prior to there so different and poor troubleshooting data from a check engine light problem resolving problem more difficult. early warning light of nature set to illuminate based on mileage. an oxygen sensor one of things meant to be replaced mileage hit. like current "change oil lights� set based on a pre-set mileage. to start testing for check engine light, you�ll need to find codes from computer, match code to troubleshooting procedure, follow procedure to find source. repair source, light go out if only problem. there "monitors" or self tests computer runs car through a drive cycle, if a problem occurs, may not run all of self tests until problem taken care. there self-tests for oxygen sensor circuit, egr system, evaporative system to name a few. therefore, another problem may exist. emission related. or hook up a scanner capable of clearing codes, and hope won�t come back on. but don�t bet on it. lastly, disconnecting battery in some cars clear memory of computer and may temporarily turn light off. beware may also cause problems such as car not rembering it�s idle and have to relearn it, radio may be rendered inoperative or in case of new toyotas, air bag blow.
Q: causes p0300 p0302 p0303 and p0304 on-board diagnostic codes for a 1997 toyota camry?
Answer : engine misfires. p0300 corresponds to misfires random among all cylinders, whereas p0301-p0306 correspond to specific cylinders. i'm not an expert, but posts have read seem to suggest because getting misfires across more than one cylinder, it's probably something like ignition coil, distributor, etc. !
Q: quarts of transmission oil needed for a 1995 toyota camry?
Answer : 4.4 quarts
Q: valve seals installed on a 1997 toyota camry 4 cylinder 2.2?
Answer : like a boss
Q: transmission fluid capacity on a 1999 toyota camry?
Answer : call parts department of a local toyota dealer and ask question of them. transmission (drain and refill): 2.6 quarts differential: 1.7 quarts. if going to change transmission fluid not forget to change fluid in differential. even system cleaner by itself but accumulates small pieces of metal with time. also toyota not recommend to use full synthetic fluid in 97-99 camry model. experience shows have a point. especially it's not recommended for old transmissions.
Q: a 1987 ford taurus 3.0 liter v6 4-door engine cooling fan controlled?
Answer : there a fan controller underneath a plastic cover on top of radiator
Q: replace inside drivers side door handle on a 2000 vw beetle?
Answer : replace inside drivers door handle by removing door panel. with door panel removed door handle mechanism be visible. remove linkage from door handle. remove door handle retaining bolts. reverse process to install new door handle.
Q: fix an automatic shoulder harness stuck in driving position on 1988 toyota camry?
Answer : there be several things causing this. take to an auto trim shop.
Q: turn off 'check engine' light on a 99 volvo s80?
Answer : yes, but with provision there no problems as seen by car's computer. disconnect negative battery cable for a couple of minutes then reconnect. erase any trouble codes stored in computer. if everything okay, check engine light stay off. if computer sees a problem, check engine light come on again.
Q: fix a dead windshield washer in 1997 toyota camry le?
Answer : underneath washer holding tank pump motor.
Q: take out fm radio on a 1998 toyota camry?
Answer : easy to remove fm radio. may have to 1st remove ashtray. then using either a l shaped or curved pic tool pry plastic frame off encompasses radio,and temp controls. be careful prying cover not to dent nor damage soft dash board around plastic cover. may have to pry farely hard to release hidden clips holding cover in place. by using pic tool slide under one spot of cover to find 1 of 4 or 5 hidden cover clips then pry to release found clip from corresponding clip hole in dashes frame. repeat for clips then hang cover to side still attached to cig lighter.then remove 4 bolts holding radio in place. pull out then unhook two wire harenessesfrom back of radio. hooking up a different radio try to obtain a matching wire hareness connector so as not to cut orginial in car wire hareness.
Q: change high mounted stoplight bulb on a 1995 lexus es300?
Answer : i'm almost positive 1994 es300 same as '95....it took me a while to figure out to take cover off without breaking anything, however, can't be gentle with it....ok, so know 3rd light all one piece... grab a hold of and pull toward you.not at an angle straight toward and be able to unclip becareful not to tare wiring so pull but don't pull to wires break off....then once get off, unplug wires so replace bulb. then install in reverse order... .... jp
Q: replace backup light switch for toyota camry le 1994 model?
Answer : make sure left side trunk hinge did not cut wires to backup lights before buy any switches. walter hi walter, right wiring in trunk got cut. thanks for suggestions, saved me some money :) himanshu
Q: remove dashboard in a 1993 toyota camry le 4 cylinder?
Answer : need to purchase or borrow a factory repair manual and follow step by step to avoid breaking something may not be able to be repaired short of replacement. leaving any part of dashpad or panels unsecured leads to improper fit and annoying rattles and vibration noises.
Q: replace air filter located on a 2003 buick century?
Answer : replace air filter on a 2003 buick century... open hood. go to driver's side. look down right behind driver's headlight. there a rectangular black box with 5" inch air intake made of a plastic bellows material. sticking out of box. on top of box (filter housing) there 2 clips on undo clips. notice open housing a little and see filter seal. also note filter <b>still</b> not be removed from housing. need to remove entire cover have to get air filter out. to take air intake duct out of way to remove entire face plate. simply take duct work off filter housing by loosening hose clamp hold in place. once take off move duct work out of way. (it flex) now pull up on cover towards you. pull filter out and replace it. put all back together by doing complete oposit and finished!
Q: replace tail light switch on a 1995 toyota camry?
Answer : one on dash marked "tail lights"? < sarcasm if crawl into tail pipe while engine reving at full throttle . . . try replacing a bulb or fuse before crawl into tailpipe.
Q: replace cv joints in a 1992 toyota camry?
Answer : take to a mechanic! agree with last answer, an independent one. replace shaft, not jont-not worth doing joint! changing front cv joint on a 4-cylinder (1987) easy. napa sells half-shaft with a new boot and cv joint for less than $70. took longer to get car jacked up, to read manual, finding out don't have to disconnect any of steering parts (on pax side) tell too in manual, and general 1st time caution, than actual job. if to change again think be done in less than a 1/2 hour. most difficult step removing (not as difficult as replacing) and replacing new shaft into tranny. need to use a wooden block for replacement (long 2x4) and large sledge. (the replacement) be a two man operation regardless of tools of choice. may find a special tool for but to use effectively need to dis-assemble more of wheel assembly necessary if using wood/sledge approach. common sense be applied during all stages of frustration. good luck!
Q: remove and replace a dashboard on a 1994 camry le?
Answer : 1994 honda camry dashboard held in place by 12 retaining clips. pry outward on each retaining clip. dashboard come off in three pieces. reverse process to install new dashboard.
Q: any years or models of toyotas have a radiator fit a 1991 toyota camry?
Answer : check out from ebay and said mostly model from 1987-1991 use same radiator. a quick check from ebay 1987-1991 toyota camry radiator - replacement radiator brand: replacement part number: p870 condition: part brand new! notes: radiator -- quality stock replacement, 4cyl; 2.0l; 122c.i, ground shipping only<ul><li><ul><li><ul><li>please read notes before buying ***</li></ul></li></ul></li></ul> $92.96 make model years engine - chassis toyota camry 87 - 91 2.0l, 4 cylinder - camry
Q: replace tail light on a toyota sienna?
Answer : depending on year but most late modles have bulbs screw in fron rear. sometimes have to remove light assy .
Q: replace radiator on a 1993 toyota camry?
Answer : manual tranny easier. automatic have 2 more pipes for transmission oil empty rad first from tap at bottom. out of sight most of time. remove fan assembly electric connector and bolts ( 4) if automatic unplug 2 oil lines from radiator .remove top and bottom rad hoses and rad top mount then pull rad out above correct. here a diy with pictures to help done by yours truly. http://www.toyotanation.com/forum/showthread.php?t=277202 copy and paste link into web browser.
Q: make a 1986 toyota camry lose power after driving for awhile?
Answer : check fuel filter and catalatic convertor.
Q: replace spark plugs on a 2002 santa fe v6?
Answer : (rear plugs) 1- remove engine cover 2- remove back left throttle cable/ground strap small bracket bolt 3- remove front two throttle cable bracket bolts 4- remove electrical connector left of rear throttle cable main bracket 5- remove vacuum hose from left side of vacuum solenoid (don't know unit but right below main throttle cable bracket) 6- slip vacuum solenoid off of bracket by pushing towards driver's side 7- remove two bolts holding main throttle cable braket (note: bolts also hold a second bracket holds vacuum solenoid) 8- remove three rear plenum tie down bolts. left one see from left side, right one right below throttle cables about an inch from right edge of plenum, and center one under main throttle cable bracket. not reinstall center bolt reversing process. without center tie down bolt may be able to skip steps 3-8. didn't check so still unknown. 9- unclamp black rubber intake hose from throttle body and push under throttle body 10- remove hose from the pcv valve at top right of front valve cover 11- remove nuts and bolts holding front of plenum (2 nuts, 2 long bolts, 3 short bolts) 12- lift plenum off studs 13- place a rag over intake manifold so don't drop anything into engine 14- tilt plenum up on passenger side about 45 degrees and brace up with a 6-8" long piece of wood or equivalent 15- change rear plugs takes about 45 min for an experienced machanic and an hour to an hour and a half for someone else. got instructions from site: http://www.santafemods.com/. don't recommend gap setting mentions on website. get a little more get up and go, but lose 3-4 mpg. (good guidance, want to add a couple missing things. under throttle body 2 coolant lines tied in come off as well as three electrical connections on driver side of plenum and 2 underneath come off as lift it. left middle rear bolt out as instructed and makes sense to reduce time needed for future plug/cable work. also, recommend changing all plug wires while going through so trouble. for me a failed cable on cylinder 4(front middle). thank for post, suv runs great.) get rid of thing total crap
Q: last dashboard symbol on left below temperature gauge indicate on a 1997 toyota camry xle v-6?
Answer : real light signal. if have a brake or signal light burnt out in back end light. if a short if light and go out intermittatley. there also a list of lights indicate in owners manual. .
Q: install brake pads on all 4 wheels of a 1991 toyota camry le with a v6 engine?
Answer : get a manual on car from discountautorepairmanuals.com for about $9 and help on next repair.
Q: reset 'check engine' light on a 2001 toyota camry yourself?
Answer : disconnect negative battery cable for a couple of minutes, then reconnect. erase codes in computer makes check engine light come on. if everything okay, check engine stay off. tried exactly advice on 2001 camry....and worked like a charm!!!
Q: replace thermostat on a 1988 toyota camry?
Answer : thermostat located on engine block. follow top water hose leading to engine. thermostat located inside water intake. remove hose. remove water intake(two bolts)housing. replace thermostat. .
Q: remove starter from a 1991 cadillac eldorado?
Answer : get a manual on car from discountautorepairmnuals.com and help on next repair also.plus pictures.
Q: reset 'check engine' warning lamp on a 1996 toyota camry v-6?
Answer : only clear with an obdii (two) diagnostic scaner
Q: remove driver's side cv joint on a 93 probe gt with abs?
Answer : pull real real hard come
Q: parking lights stay on after car turned off causes car battery to run down on a 1991 toyota camry fix this?
Answer : turn stupid headlight switch off. deedeedee have same problem with 87 camry. need to change stop light switch.
Q: replace outside passenger mirror on a 1996 ford thunderbird?
Answer : to not too long ago. have to get off door panel....lots of fun. first have to pop off light cover on door. theres a reallllly long screw behind that. next, take off panel window control on it. use a screw driver, but be careful to not scratch plastic too much. thewres a bunch of wiring right behind so unclip and put out of way. start unscrewing things and rest come easily.the main door panel held on by a series of clips. pry back panel w/a screwdriver or something like that. if a clip breaks ok trust me!the rest playing w/hard to reach wires and stuff.good luck!
Q: fuel filter located and replace on a 1998 plymouth voyager?
Answer : <br/>fuel filter located directly on fuel tank. must drop tank to access quick connect lines. <br/>thank ,you helpfull,good luck.
Q: a 1993 camry 4-cyl did not pass smog test reading 1400 for nox max 700 egr valve bad or there more to fix?
Answer : with nox numbers high, says egr system isn't working correctly. at idle, egr closed. at speeds, egr open. see if move egr valve diaphragm by hand car idling. car die or want to die. if doesn't this, be plugged up. remove egr valve and clean any carbon deposits in valve and also same on engine side egr connected. also, to reduce nox emissions reading, replace spark plugs, wires, distributor cap and rotor. then, retard timing as as possible. be done by loosening 10mm nut next to distributor and turning clockwise, then re-tighten bolt.
Q: deactivate an after market alarm on a 1993 toyota camry?
Answer : find wire feeding voltage and clip it.
Q: locate reset button for 'maintenance required' light on a toyota camry 2004?
Answer : read owners manual in glove box. have in index light talking about. or find picture of dash components in owners manual and read description and go from there. it's trip meter reset sticking out of spedo lens. turn engine off with odometer reading[mileage] showing. turn ignition switch to "run" position. hold trip meter reset "button" down for five seconds or more. see 0000000000 showing,release button. odometer reading appear and light be out. have to once a year since only drive about 7500 miles a year.
Q: replace automatic console light in toyota corolla 1995?
Answer : bulb directly under "prnd21" on bottom, removed by a 1/4 turn counter clockwise twist. if can't get by reaching under edge of console, take 7 screws out of console and raise up some.
Q: change car door locks?
Answer : most models of cars be re-keyed. order a complete set of locks from a motor parts store or a locksmith. also, a locksmith re-key existing locks.
Q: turn off engine idiot light on a 1996 camry?
Answer : take to a mechanic, basically means there some problem with car. disconnecting battery cables for about 15 minutes cause light to temporarily reset, but not fix problem light indicates. may last for a days or up to several months.
Q: change front pads and rotors on a 1994 ford tempo gl 4-cylinder?
Answer : need a t-45(the manual advised and car required a t-40) torx socket, a ratchet to fit, a slot screwdriver and a small amount of grease. 1- loosen lug nuts (don't remove) 2- jack up car 3- place a safety stand (under sway bar knuckle easy) 4- remove lug nuts and tire assembly 5- using a slot screwdriver pry between inner pad and rotor (this push caliper piston in) 6- remove two caliper bolts with torx socket(they behind caliper pointing toward and covered by a rubber sleeve) 7- slowly pry caliper straight out (note pads installed) 8- not let caliper hang by hose!!!!!! 9- install new pads (note inner and outer different) 10- put a small amount of grease on caliper area slides on steering knuckle 11- if replacing rotors too, slide off old rotor and slide on new rotor 12- slide caliper and pad assembly onto rotor (sometimes put a lug nut on to hold rotor straight) 13- tighten caliper bolts to 20ft.lbs (being bolts pointing toward so make sure tightening and not loosening them) 14- reinstall wheel and tire assembly note: always brakes in sets not one side pump up brakes before putting vehicle in gear listen for any noises on test drive make a light stops them let pads cool for at least 30 minutes to seat new pads happy braking hope helped x s f h p
Q: thermostat located on a 1998 oldsmobile intrigue?
Answer : at end of upper radiator hose inside thermostat housing. easy to remove, two screws. unless it's a 3.5, then attached to housing, screwed into pulley side of front (right) cylinder head, attached to lower hose, bypass hose, and coolant recovery tank hose.
Q: fix a power window on a 1990 camry rolls down but not up?
Answer : track may not be align and binding somewhere inside. have to remove trim and plastic water seal so have a better view. if roll window manually better but first have to disconnect wiring harness from power window motor. if not try to roll up and down using own switch and check binds necessary adjustment. check also window gasket maybe culprit. goodluck.
Q: be wrong with a trunk lid of a '91 toyota camry stuck open?
Answer : check latching mechanism, move all moving parts around and lubricate w / spray on grease. use a screwdriver to push moving parts around, saves on pinched fingers! also-check to see if inner release latch returned to closed position.
Q: change headlights on a 2002 mustang?
Answer : to change headlights on a 02 mustangi did today...(2002 mustang gt) open hood on back of headlight assembly, there's a long metal clip. holds entire assembly in place, take out using tabs (gently). whole assembly slide right out, then unscrew large plastic nut holds bulb in place. to remove bulb twist. it's pretty easy to and takes zero tools (yay). foglight bulbs a different story. still trying to figure out. . erik
Q: previous owner put a loop on heater core find out heater hoses go on engine of a 1985 camry?
Answer : if disconnected heater core, means leaking. get a manual on car from parts store and show to replace heater core also
Q: correct psi for tires on a 1996 toyota camry?
Answer : on side of tire read {max air pressure} the answer on inside of driver door, look around open car door. tell tire pressure be if original size and tire from manufacture of car. 32 psi pretty common for all passanger vehicles
Q: dashboard brake light on in a 1994 cherokee mean need new brakes?
Answer : try checking brake fluid level if ok then cxheck pad wear.
Q: one find a wiring diagram for stereo in a 1990 toyota celica 2dr hatchback?
Answer : try website www.the12volt.com a car audio website but wiring diagrams for all vehicles. hope helps
Q: reset radio in a 1995 camry change battery?
Answer : manually tune to favorite station. once have a station want to store in memory, press down and hold button want staion to correspond to. repeat procedure for all of available programmable buttons.
Q: lock adjustable tilt steering wheel into position on a 1989 toyota camry?
Answer : lever located on bottom of steering column. if it's not locking, lever may be jammed and need to wiggle a bit.
Q: change broken door handles on a 1993 camry le 4-cylinder?
Answer : have to take door panel off and make sure window up and two bolts to take off
Q: adjust windshield wipers on a 1999 toyota camry so not squeak and rub too hard raining?
Answer : there a lot of us have same problem. there no adjustment. only thing get new blades/refills for wipers.
Q: timing belt need to be removed to change water pump on a 1994 galant?
Answer : on quite a of type vehicles, answer yes- but- need to go to a car parts store, and get a repair manual for car. cost about $16.00
Q: replace driver's side outside door handle on a 1996 toyota camry?
Answer : well first need to take off door panel, then there two 10mm bolts hold handle on, remove and diconect bar for lock and come out. -- hah funny, good one. remove door panel and it's impossible to reach bolts. so now, thanks to vague answer, door panel off and, as usual, won't go back on correctly. maybe don't have proper tools...or long skinny alien arms reach into tiny dark spaces to left. replaced front driver side door handle on 96 camry - here's story: 1 - take door panel off. a screws and a couple of clips. inside door handle trim needs to be removed as well - tricky, latch for trim on bottom left side, so be careful prying out - broke mine. disconnect power cable to windows/door switch panel. make sure window up. 2 - ok, here saw 3 10mm bolts hold door handle and panic set in. one relatively easy to get to a straight line thru door's sheetmetal (there a hole), but third way inside. after about 30 min struggling with getting a ratched in there proceeded to get to 2 bolts and lo and behold handle popped out. there only 2 bolst holding handle to door frame, third bolt hold lock to door handle. 3 - pull handle out (you may have to wiggle handle a bit, place a rag between handle and door to avoid scratches), unbolt 3rd 10mm bolt. remove rod attached to door handle, to break funny plastic clip holds rod to door handle. 4 - bolt 3rd bolt to new handle. attach rod to handle thru plastic clip - be extra careful here, not want to break plastic clip - be hard to find. used plier to gently push rod thru plastic hole and than swung clip's clamp to latch onto rod. push/wiggle handle back in place. bolt two 10mm bolts from inside door. 5- connect wiring harness to windows/door switch. attach panel back. took me a little more than an hour to this, including panic time.
Q: replace headlights on a 1997 toyota camry?
Answer : need to do, take off front bumper to allow easy access take off screws and clamps holding in place. also half to take out turn signals as connected to headlamp assembly. any questions email me at anthony.wiles@gmail.com . anthony
Q: replace a passenger side powered mirror on a 1995 toyota camry?
Answer : remove door panel and mirror held on with bolts.
Q: replace rear brakes on a 1989 toyota camry?
Answer : need to go to a car parts store, and get a repair manual for car. cost about $16.00 or, go to a public library
Q: replace thermostat located on a 1996 dodge ram 1500 4x4 360 magnum 5.9l?
Answer : u unbolt outlet---- (gooseneck) upper radiator hose connects 2 engine-- clean gasket-or o-ring surface b 4 u install new thermostat-be sure 2 install thermostat correct way b cause some b installed backwards & u toast engine due 2 overheating. i'd like to add drilling a couple of <i>small</i> holes (1/8" or 3/32") on flat part of thermostat (near valve seat while closed) allow air bubbles (which otherwise be trapped inside engine block thermostat closed) to harmlessly flow into radiator. helpful re-filling radiator tank. need to drain antifreeze out of radiator below thermostat housing before remove thermostat housing or have antifreeze going everywhere.
Q: remove tail light lens on a 2000 vw beetle to replace bulb?
Answer : let's pretend driver side rear bulb need to be replaced: 1- in trunck, remove left panel covering back of light (it's approximately 4"x6") no tools reaquired, pull out. 2- there 's a black knob inside need to remove, again with bare hand. 3- now stupid part: looking at rear of car, around light, need to insert a tiny screwdriver between light casing and car body to unlock casing. where? looking at casing,pretendind it's a watch there 2 locks located at 4 o'clock and 5 o'clock. personnally used a plummer plunger on casing to pull out a bit to see locks. double checked procedure with ma volks dealer...
Q: correctly replace water pump and timing belt on a 1998 dodge durango?
Answer : ==new answer headline==this question not too involved to answer here. takes some explaining as with any repair by home mechanic. 1. remove serpentine belt by rotating main tensioner clockwise. may want to leave on to apply pressure loosening nut for fan, however not always work. 2. 4 bolts retain fan shroud. simply loosen but not remove all of bolts until fan nut loose. 3. there supposed to be four bolts on water pump pulley to apply counter pressure with a 13mm wrench loosening fan nut (this nut reverse threads so it's not righty tighty, lefty loosey.) at point might want to remove idler pulley right above water pump to make following steps easier. 4. manual says need a special tool to loosen fan nut. couldn't buy at auto parts store because water pump pulley both on old one and new one did not have 4 bolts but unthreaded holes instead. dodge not tell me in situation or sell any special tools to customers. rude. so used a strap wrench and wrapped around pulley and held tight while unloosened fan nut. worked great. 5. once fan nut loose, remove bolts for shroud and lift fan and shroud out together. 6. there three hoses (on v8) need to be removed from water pump. need needle nose and pliers to this. 7. mark bolt at 12 o'clock on pump for reference and start loosening them a little at a time clockwise laying them down in order as different lengths. 8. remove water pump and get ready to start scraping gasket. upper part difficult to see but be persistant. wants to see a leak after all work. 9. water pump a coolant return hose need to be transfered to new pump and a new o-ring replaced included. 10. apply rtv high temp. silicone to new water pump and side of gasket faces engine. spread thin. to break habit of thinking more silicone=less chance of leaks. 11. install new pump and gasket and torque bolts in 1/4 turn increments. let silicone cure as instructed on package. 12. start working way back up list, reversing procedure, refill coolant leaving radiator cap off. start engine and turn on heater. add coolant mixture as necessary until full. check for leaks and hope new pump lasts a darn long time. question ask too involved for a proper answer. need to go to a car parts store, and get a repair manual for car. cost about $16.00 or, go to a public library.
Q: remove driver side door panel of a 1991 camry?
Answer : see related links below for a really good step by step guide. following some minor noted differences: armrest for 91 model a padded cover to be removed from top to access two of screws. pry cover up on side closest to front of car with a screwdriver and work way back. on back end a plastic hook release from forward movement of popping rest of cover up. inside door handle trim needs to be released in two places, not one shown. first release as shown by inserting a small screwdriver into crack between handle and bottom trim handle hinges and push up on screwdriver handle to release. then insert into crack between lock lever and top trim and push down on handle to release top side. then continue as shown in directions. note door handle trim one thing most trouble with. if don't know trick with screwdriver release then end up having to destroy trim to get off.
Q: replace drivers outer door handle on a 1992 toyota camry?
Answer : go to website autorepair.about.com and have step-by-step instructions. good luck!
Q: change low beam headlights of a 1993 toyota camry?
Answer : take light assy off of car and turn bulbs counterclockwise to remove blubs
Q: change dome light in a 1999 toyota sienna?
Answer : if it's one push light cover to turn on, change it: on side of cover presses up, slide in a thin screwdriver--and mean thin because cover hinges break. there a small clip release and cover pop out.
Q: get a 97 camry's dome light cover off?
Answer : there no screws in dome light cover of a 1997 toyota camry. pry cover off with a flat bladed screw driver.
Q: an 'idle cylinder'?
Answer : an idle cylinder refers to state engine not coupled with drivetrain and with throttle pedal not depressed. there rotational speed but not enough to move vehicle.
Q: change inside door handle on 1999 hyundai elantra 4 door 4 cylinder?
Answer : unscrew door handle. unscrew "cup" pull on to close door. unscrew rest of screws around bottom and rear of door panel. slide door handle sideways and pull free. need to unclip long metal rods from back of handle, may be easier with arm inside door panel. <br> <br> put back opposite of took apart. <br> <br> stocker @ http://www.rdtiburon.com/ <br> david @ http://votefordavid.blogspot.com
Q: difficult be to replace burnt out light bulbs in a 1996 villager instrument panel?
Answer : need to go to a car parts store, and get a repair manual for car. cost about $16.00 or, go to a public library.
Q: change steering wheel lock assembly in a 1992 gmc sierra?
Answer : question ask too involved for a proper answer. need to go to a car parts store, and get a repair manual for car. cost about $16.00 or, go to a public library. remove steering wheel-use a special tool 2 compress lock plate & remove snap ring-unscrew special tool & remove lock plate-butt check pin goes through lock plate 2 lock it.if pin doen't go through plate key removed-there"s another problem -like plastic actuator pieces
Q: replace ignition lock without key?
Answer : drill through lock. there a "gear" on back of lock. try not to drill through it. after drill through lock use a screwdriver to turn gear to right position (run or acc )depending on kind of car have. then all have to remove steering wheel and mis. parts to get to a screw holds ignition switch in. then remove lock and install new one.
Q: 1997 toyota camry overheated because fans stop working and now car sputters engine ruined?
Answer : ok iv smae problem im 94 replace therostat... cant go wrong with only like 4 bucks and easy to install.. dont go to a mechanic! wanted 80 bucks only to undo 2 lug nuts and placed in poped on and weird but for some reason idk y but car over heat a times after words but stop trust me a friend tell me same thing and thought bull hes being honest.. also be engine coil or distrubuter cap... car have a hard time starting up in rain or after rains? termosate controls fans... if engine over heats let me remind u there no heat sensers in engine and if gets too hot frie coils... happened to me... but anyways replace termostat... promise a great improvment =d any more questions email me at blunt101@gmail.com
Q: replace rotors on a 1992 toyota camry xle?
Answer : after remove calipers, come off with a slight tug. if not, then apply penetrating oil around seam of hub and rotor meet, replace lug nuts- a threads, and then tap on rotor gently with a hammer to help free rust.
Q: change dome light in a saturn 1998 sl1?
Answer : changing a saturn dome lamp(i changed dome light on 1999 saturn sedan. ) 1. remove clear plastic cover: important: turn dome light switch to "off". on passenger's side of dome light there a small, rectangular opening (a slot). stick a flathead screwdriver deeply into slot in order to press a catch inside. clear cover swing open on "hinges". popped cover out of hinges for easy access. 2. remove old bulb: move bulb forward (towards front of car). bulb supported by two silver-colored contacts (little pieces of metal). move bulb forward a little and up a little while pushing one of contacts towards one. slide old bulb out. 3. connect new bulb: bulb number for a 1999 saturn sedan 562. slide new bulb onto contacts while squeezing contacts together. turn dome light switch to "on" to see if bulb works. 4. replace clear plastic cover: pop cover back on hinges. swing cover back into place. 5. if worked, then help someone else!
Q: turn off check engine light without having car serviced?
Answer : on a lot of cars u unhook one of battery cables for a minutes and light stay out. check engine light illuminated because there a problem with one or more of control devices on engine. a responsible way of having taken care of, be to take to a shop repair vehicle. go to autozone, read code for you, then then to clear it. if keeps coming back i'd go to a garage at point.
Q: replace fuse associated with alternator in a 1989 toyota camry?
Answer : if new fuse installing a hole in one of terminals, carefully check location, because hole means a bolt going through it> may have to unbolt fusebox(underhood right?) carefully tip upside down, and remove bolt> probably a 10 mm socket required> .
Q: park neutral switch on a 1987 toyota camry?
Answer : on '88 camry 4-cyl, neutral safety switch in front, behind radiator, on transaxle case. for an87 and better data, ask question with name of component, as above. good luck. how to tell whether 1987 toyota camary motor locked up
